YouvBeenThumped
RRCRat Rig Community [Unofficial]
•Created by drops on 5/31/2024 in #ratos-support
RAT OS 2.1 RC1 Homing Issue
I just hate when sd cards cease to be sd cards
37 replies
RRCRat Rig Community [Unofficial]
•Created by drops on 5/31/2024 in #ratos-support
RAT OS 2.1 RC1 Homing Issue
I don't use SD cards. NVME drive
37 replies
RRCRat Rig Community [Unofficial]
•Created by drops on 5/31/2024 in #ratos-support
RAT OS 2.1 RC1 Homing Issue
Im working up the courage to attempt it currently
37 replies
RRCRat Rig Community [Unofficial]
•Created by drops on 5/31/2024 in #ratos-support
RAT OS 2.1 RC1 Homing Issue
37 replies
RRCRat Rig Community [Unofficial]
•Created by drops on 5/31/2024 in #ratos-support
RAT OS 2.1 RC1 Homing Issue
Until you hit it.... And the printer keeps going cause it hasn't registered the command :FLASHBANG:
37 replies
RRCRat Rig Community [Unofficial]
•Created by YouvBeenThumped on 5/30/2024 in #fix-my-printer
Super Power motors on 5160 Pro's 48V
Increased run_current to 2.4 and fixed issue
4 replies
RRCRat Rig Community [Unofficial]
•Created by YouvBeenThumped on 5/4/2024 in #fix-my-printer
MCU Not connecting. Klipper Log provided. After swapping from Octopus V1.1 to Pro h723 V1.1
I have no clue why that works... Typically if I did that in the past with something else. It would error out about the alias
18 replies
RRCRat Rig Community [Unofficial]
•Created by YouvBeenThumped on 5/4/2024 in #fix-my-printer
MCU Not connecting. Klipper Log provided. After swapping from Octopus V1.1 to Pro h723 V1.1
@Hunterprime figured it out by just pissing in the wind :kekw: :GUNPEPE: :AngeryPing:
18 replies
RRCRat Rig Community [Unofficial]
•Created by YouvBeenThumped on 5/4/2024 in #fix-my-printer
MCU Not connecting. Klipper Log provided. After swapping from Octopus V1.1 to Pro h723 V1.1
18 replies
RRCRat Rig Community [Unofficial]
•Created by YouvBeenThumped on 5/4/2024 in #fix-my-printer
MCU Not connecting. Klipper Log provided. After swapping from Octopus V1.1 to Pro h723 V1.1
18 replies
RRCRat Rig Community [Unofficial]
•Created by YouvBeenThumped on 5/4/2024 in #fix-my-printer
MCU Not connecting. Klipper Log provided. After swapping from Octopus V1.1 to Pro h723 V1.1
I tried reflashing and get the same issue
18 replies
RRCRat Rig Community [Unofficial]
•Created by YouvBeenThumped on 5/4/2024 in #fix-my-printer
MCU Not connecting. Klipper Log provided. After swapping from Octopus V1.1 to Pro h723 V1.1
It's all good
18 replies
RRCRat Rig Community [Unofficial]
•Created by YouvBeenThumped on 5/4/2024 in #fix-my-printer
MCU Not connecting. Klipper Log provided. After swapping from Octopus V1.1 to Pro h723 V1.1
18 replies
RRCRat Rig Community [Unofficial]
•Created by YouvBeenThumped on 5/4/2024 in #fix-my-printer
MCU Not connecting. Klipper Log provided. After swapping from Octopus V1.1 to Pro h723 V1.1
ok
18 replies
RRCRat Rig Community [Unofficial]
•Created by YouvBeenThumped on 5/4/2024 in #fix-my-printer
MCU Not connecting. Klipper Log provided. After swapping from Octopus V1.1 to Pro h723 V1.1
Here is the Printer.cfg as well.
18 replies
RRCRat Rig Community [Unofficial]
•Created by lucasdm303 on 4/21/2024 in #fix-my-printer
Front right Z motor not working
I don't see the coupler twisting so I don't think its a binding issue
10 replies
RRCRat Rig Community [Unofficial]
•Created by lucasdm303 on 4/21/2024 in #fix-my-printer
Front right Z motor not working
You could try moving the stepper driver to a different Z stepper spot and see if the problem moves.
10 replies
RRCRat Rig Community [Unofficial]
•Created by Daxxer on 4/20/2024 in #fix-my-resonance
VC3.1 500. I am getting some belt binding
So for starters. Since yours is naming both belts a number. I would loosen one belt a bunch. Just so you know which belt is upper and lower on your graph to rule out incase you get it backwards
9 replies
RRCRat Rig Community [Unofficial]
•Created by Daxxer on 4/20/2024 in #fix-my-resonance
VC3.1 500. I am getting some belt binding
When you tighten one belt. You are tightening the other belt. That is why loosening one side and then tightening the other side is key
9 replies
RRCRat Rig Community [Unofficial]
•Created by Daxxer on 4/20/2024 in #fix-my-resonance
VC3.1 500. I am getting some belt binding
Also check all bearing stacks hardware that nothing has backed off while belts are loosened.
9 replies