blacksmithforlife Comments - Answer Overflow

blacksmithforlife

•Created by Aron on 2/23/2025 in #ratos-support

Update to new version

Not knowing which specific version you are on (because you didn't say), but in general yes you will need to reflash as 1.x -> 2.x is a reflash, and 2.0.x -> 2.1.x is a reflash right now

5 replies

RRCRat Rig Community [Unofficial]

•Created by PickleSmothie on 2/22/2025 in #fix-my-printer

Probe and Endstop Z always triggered

what did you select in the configurator? Looks like you chose probe which I believe is incorrect if you are using beacon

12 replies

RRCRat Rig Community [Unofficial]

•Created by PickleSmothie on 2/22/2025 in #fix-my-printer

Probe and Endstop Z always triggered

did you copy this config from another machine or something? Why does it have z_offset_probe and probe that is set to pin: ^toolboard_t0:probe_pin # For NPN NC probes such as the Super Pinda / Vinda / SupCR / Decoprobe probes.?

12 replies

RRCRat Rig Community [Unofficial]

•Created by PickleSmothie on 2/22/2025 in #fix-my-printer

Probe and Endstop Z always triggered

To fix the always triggered probe - what kind of probe do you have?

12 replies

RRCRat Rig Community [Unofficial]

•Created by PickleSmothie on 2/22/2025 in #fix-my-printer

Probe and Endstop Z always triggered

To fix your bed moving in the wrong direction: lines 88, 98, and 105 change to add ! like this:

dir_pin: !z0_dir_pin
dir_pin: !z1_dir_pin 
dir_pin: !z2_dir_pin

dir_pin: !z0_dir_pin
dir_pin: !z1_dir_pin 
dir_pin: !z2_dir_pin

12 replies

RRCRat Rig Community [Unofficial]

•Created by fredz on 2/22/2025 in #ratos-support

RatOs invalide

I am trying to figure out if you are on the correct subnet - but I can't if you refuse to give us the IP address. Your local address is only good for your network if you are worried I am trying to attack you or something

39 replies

RRCRat Rig Community [Unofficial]

•Created by fredz on 2/22/2025 in #ratos-support

RatOs invalide

what's the IP of the computer you are using for SSH? And what is the IP of your raspberry pi?

39 replies

RRCRat Rig Community [Unofficial]

•Created by fredz on 2/22/2025 in #ratos-support

RatOs invalide

putty wants the hostname or IP, http is for websites, not ssh

39 replies

RRCRat Rig Community [Unofficial]

•Created by lingo124 on 2/22/2025 in #ratos-support

RatOS Post-Processing Introducing Errors in GCode (More like destroying good GCode)

@miklschmidt and @Helge Keck

31 replies

RRCRat Rig Community [Unofficial]

•Created by guesswhatsthisparlor on 2/17/2025 in #fix-my-printer

X stopped working when changing to Hybrid

I haven't done a hybrid setup

422 replies

RRCRat Rig Community [Unofficial]

•Created by rip4318 on 2/16/2025 in #ratos-support

Octopus Pro 446 and RatOS firmware not updating

ratos 2.1 RC3

6 replies

RRCRat Rig Community [Unofficial]

•Created by ThatLadBoniface on 2/19/2025 in #ratos-support

Prusa Einsy Configuration Issues

yeah that bug was fixed in 2.1, for now just ignore it and move on

16 replies

RRCRat Rig Community [Unofficial]

•Created by connieveren on 2/18/2025 in #ratos-support

Can not open RatOS in the browser

what is the IP of the pi, and what is the IP from where you are trying to access the pi? It could be they are on different subnets

17 replies

RRCRat Rig Community [Unofficial]

•Created by OldKingHamlet on 2/19/2025 in #fix-my-printer

I am at an absolute loss. Scratching noise coming from rear motor motor/bearings, V-Core 3.1

I hope your steppers were disconnected for that movement, otherwise you might fry them from the steppers acting like generators. Anyways, use a screwdriver as a stethoscope to hear where the sound is coming from. Using a specific Hz isn't a good way to tension the belts, use the built in macros. You probably over tightened the belts and have caused premature failure

5 replies

RRCRat Rig Community [Unofficial]

•Created by Rissen on 2/18/2025 in #ratos-support

can´t flash Octopus V1.1 - Core-V4 500 IDEX

try using ratos 2.1 instead, if you still have issues upload your debug.zip

13 replies

RRCRat Rig Community [Unofficial]

•Created by Roughneck on 2/18/2025 in #ratos-support

Merc 1 Hydra RatOs 2.1

As per the rules, upload your debug.zip please

6 replies

RRCRat Rig Community [Unofficial]