archen
RRCRat Rig Community [Unofficial]
•Created by archen on 12/8/2024 in #fix-my-printer
Octopus Pro 1.1 h723 fried
However some more stuff on the board are damaged like many endstop inputs so I had to move the VAOC Z endstop to X endstop that where free.. Everything else seems to work. Reading the schematics it looks like the inputs goes directly to the mcu. Not sure it's worth changing it for 10€. I'll probably just stick with my custom assignment of Z endstop
7 replies
RRCRat Rig Community [Unofficial]
•Created by archen on 12/8/2024 in #fix-my-printer
Octopus Pro 1.1 h723 fried
Replacing U24 solved the issue
7 replies
RRCRat Rig Community [Unofficial]
•Created by archen on 12/8/2024 in #fix-my-printer
Octopus Pro 1.1 h723 fried
Yes I have a hot air station. Waiting for components ATM
7 replies
RRCRat Rig Community [Unofficial]
•Created by archen on 11/25/2024 in #fix-my-printer
IDEX inconcistent nozzle alignment
102 replies
RRCRat Rig Community [Unofficial]
•Created by archen on 11/25/2024 in #fix-my-printer
IDEX inconcistent nozzle alignment
its a new iteration of the califlower, if you bought califlow previously you can update for 50% off
102 replies
RRCRat Rig Community [Unofficial]
•Created by WhatTheFuchs on 11/7/2024 in #fix-my-mesh
VC4 500 IDEX initial cold mesh
If you have the heater mounted I would do it in heat soaked state
14 replies
RRCRat Rig Community [Unofficial]
•Created by WhatTheFuchs on 11/7/2024 in #fix-my-mesh
VC4 500 IDEX initial cold mesh
If you tighten the ends first you will trap tensions
14 replies
RRCRat Rig Community [Unofficial]
•Created by WhatTheFuchs on 11/7/2024 in #fix-my-mesh
VC4 500 IDEX initial cold mesh
Did you tighten the x rail from one side to the other?
14 replies
RRCRat Rig Community [Unofficial]
•Created by archen on 11/25/2024 in #fix-my-printer
IDEX inconcistent nozzle alignment
Makes sense 👍 I'll print some stuff now and go back later on to fine-tune if we get better tools to work with
102 replies
RRCRat Rig Community [Unofficial]
•Created by archen on 11/25/2024 in #fix-my-printer
IDEX inconcistent nozzle alignment
Some basic knowledge of how belt drives work wouldn't hurt 🫣
102 replies
RRCRat Rig Community [Unofficial]
•Created by archen on 11/25/2024 in #fix-my-printer
IDEX inconcistent nozzle alignment
True, I'm not that concerned about it as it can be corrected with skew profile. More interested to find out why my X scale is so out when y is pretty good
102 replies
RRCRat Rig Community [Unofficial]
•Created by archen on 11/25/2024 in #fix-my-printer
IDEX inconcistent nozzle alignment
102 replies
RRCRat Rig Community [Unofficial]
•Created by archen on 11/25/2024 in #fix-my-printer
IDEX inconcistent nozzle alignment
@VisualTech48
Ran califlower calibration. Seems like x has quite an error in dimension. Skew 0.1 degrees. Is this from belts or is frame not square?
102 replies
RRCRat Rig Community [Unofficial]
•Created by WhatTheFuchs on 11/7/2024 in #fix-my-mesh
VC4 500 IDEX initial cold mesh
I pull with gantry mounted. Just don't be wreckless 🙂
14 replies
RRCRat Rig Community [Unofficial]
•Created by WhatTheFuchs on 11/7/2024 in #fix-my-mesh
VC4 500 IDEX initial cold mesh
no, you want to bend the gantry extrusion, not the linear rail
14 replies
RRCRat Rig Community [Unofficial]
•Created by archen on 11/25/2024 in #fix-my-printer
IDEX inconcistent nozzle alignment
102 replies
RRCRat Rig Community [Unofficial]
•Created by archen on 11/25/2024 in #fix-my-printer
IDEX inconcistent nozzle alignment
102 replies
RRCRat Rig Community [Unofficial]
•Created by archen on 11/25/2024 in #fix-my-printer
IDEX inconcistent nozzle alignment
102 replies
RRCRat Rig Community [Unofficial]
•Created by archen on 11/25/2024 in #fix-my-printer
IDEX inconcistent nozzle alignment
actually neither y is pretty but without going low on tension I can't get them to align
102 replies
RRCRat Rig Community [Unofficial]
•Created by archen on 11/25/2024 in #fix-my-printer
IDEX inconcistent nozzle alignment
102 replies