D00M-_
RRCRat Rig Community [Unofficial]
•Created by D00M-_ on 12/6/2024 in #fix-my-print
Wall separation and wobbly straight lines (Good graphs - Low accel) -IDEX 500
I'm doing an accel test and I'm getting wobbly lines on the x axis and wall separation on both axis. I've re done IS couple of times and the problem persist. Print is PLA with 5k accel. Well below recommended accel.
11 replies
RRCRat Rig Community [Unofficial]
•Created by D00M-_ on 11/25/2024 in #ratos-support
Web interface becomes unresponsive and doesn't connect until restart. Happens in print/ calibration
During printing or when preforming long calibration sequence the web interface becomes unresponsive, crashes and can connect at all. Ive tried to connect with the local host resolver, the ip, and to ssh into the pi. None work. The printer is still working and printing but you cant control anything. Even after the print is done the interface woun't connect until you do a hard reset. Im a add the log files for moonraker as i think there is the problem.
4 replies
RRCRat Rig Community [Unofficial]
•Created by D00M-_ on 11/3/2024 in #fix-my-printer
Filament grinding HELP
Vcore 4Printing ABS, filament grinds every print and either clogs nozzle or stops extruding. Tensioned using vez method and/or mikl method and still grinding. Helge suggested to check the gears to see if they are centered on filament path. They where not. Fixed that and it still grinds.
Open to suggestions. Im suing the stock punkfill abs profile.
Some suggestions i found online are lowered retraction (now at 120), and checking filament path. I also lubed the filament spool holder to make it move easyer
2 replies
RRCRat Rig Community [Unofficial]
•Created by D00M-_ on 10/16/2024 in #ratos-support
Im trying to use realtime analysis but im getting an error when i want to display the graph
88 replies
RRCRat Rig Community [Unofficial]
•Created by D00M-_ on 10/1/2024 in #fix-my-print
Flow Calibration Solid infill holes
12 replies
RRCRat Rig Community [Unofficial]
•Created by D00M-_ on 9/24/2024 in #ratos-support
Trying to switch a relay for lights with the octopus
I found this reddit post where someone uses the exact same relay module as me and it works. Only thing is his uses marlin. https://www.reddit.com/r/BIGTREETECH/comments/s2b9t5/switch_a_relay_with_the_octopus_v11/
No matter what I do the module is always on. Ive tried 5v rails/ 3v rails. Same outcome always. The weird thing is if I dont plug the input cable in, the relay is off, or if I plug it into an unregisterd pin its also off. But as soon as i register the pin. Its on always. Now i tried with endstop pins
[output_pin my_pin]
pin:PG11
value: 1
shutdown_value: 0
140 replies
RRCRat Rig Community [Unofficial]
•Created by D00M-_ on 9/23/2024 in #fix-my-mesh
Box was hit in shipping. Does this need to be replaced? Vcore 500
32 replies
RRCRat Rig Community [Unofficial]
•Created by D00M-_ on 3/23/2023 in #fix-my-printer
Toolboard: 4028 Fan wired correctly but behaving inverted.
Basically the title.
Ive tried all manners of trying to the the pin to invert in klipper and nothing seams to be working.
Here is the config section:
[fan]
pin: !toolboard:fan_part_cooling_pin
tachometer_pin: ^toolboard:PB8
tachometer_poll_interval: 0.0005
enable_pin: PA2
shutdown_speed: 0.0
cycle_time: 0.00004
One weird thing is that even if I put a random port on the pin line. The fan still is controllable with the slider but just inverted. Even if I delete the whole line, nothing changes.
The behavior is as follows.
0% = Fan off
1% = 100 fan
50% = 50%
85% = 0%26 replies
RRCRat Rig Community [Unofficial]
•Created by D00M-_ on 2/7/2023 in #fix-my-print
z artifacts advice
I redid my alignment on the whole printer. Is this a good result or can I do something to get it even better?
3 replies
RRCRat Rig Community [Unofficial]
•Created by D00M-_ on 2/1/2023 in #fix-my-print
z banding more visible on one side
2 replies