Teckgeek
RRCRat Rig Community [Unofficial]
•Created by Teckgeek on 1/27/2025 in #fix-my-printer
Hybrid confusion
Installed belts today for the hybrid and used configuration setup to be 500 hybrid. thing makes a awful noise as you can hear belts skipping.
My printer.cfg reads
[stepper_x]
dir_pin: !x_dir_pin # Add ! in front of pin name to reverse the direction of stepper_x
rotation_distance: 40 # 40 for 20 tooth 2GT pulleys, 32 for 16 tooth 2GT pulleys
homing_speed: 50
position_min: -59.8
position_max: 559.8
position_endstop: -59.8
#---------------------------------------------------- X1 ----------------------------------------------------
The B axis motor for the toolhead, located at the rear right of the printer
#------------------------------------------------------------------------------------------------------------
[stepper_x1]
dir_pin: !x1_dir_pin # Add ! in front of pin name to reverse the direction of stepper_x1
rotation_distance: 40 # 40 for 20 tooth 2GT pulleys, 32 for 16 tooth 2GT pulleys
#---------------------------------------------------- Y -----------------------------------------------------
The left Y motor used for cartesian Y control in Hybrid CoreXY, located at the rear left of the printer
#------------------------------------------------------------------------------------------------------------
[stepper_y]
dir_pin: !y_dir_pin # Remove ! in front of pin name to reverse the direction of stepper_y
rotation_distance: 40 # 40 for 20 tooth 2GT pulleys, 32 for 16 tooth 2GT pulleys
homing_speed: 50
position_min: -14.35
position_max: 530
position_endstop: -14.35
#---------------------------------------------------- Y1 ----------------------------------------------------
The right Y motor used for cartesian Y control in Hybrid CoreXY, located at the rear right of the printer
#------------------------------------------------------------------------------------------------------------
[stepper_y1]
dir_pin: y1_dir_pin # Add ! in front of pin name to reverse the direction of stepper_y1
rotation_distance: 40
which makes no sence to me.
14 replies
RRCRat Rig Community [Unofficial]
•Created by Teckgeek on 1/21/2025 in #fix-my-mesh
V-core 4 500
1 replies
RRCRat Rig Community [Unofficial]
•Created by Teckgeek on 8/15/2024 in #fix-my-mesh
what to adjust.
5 replies
RRCRat Rig Community [Unofficial]
•Created by Teckgeek on 7/17/2024 in #fix-my-resonance
is this a okay graph?
18 replies
RRCRat Rig Community [Unofficial]
•Created by Teckgeek on 8/6/2023 in #fix-my-printer
Octopus Max EZ with Klicky
1 replies
RRCRat Rig Community [Unofficial]
•Created by Teckgeek on 7/25/2023 in #ratos-support
Z-Steppers not functioningcorrectly
Question to those smarter then me. I have a Octopus Max EZ that I am having issues with the Z axis. When I do the stepper buzz test it works with stepper_z but gives the uart IFCNT error when I try Z1, Z2 etc. If I change say Z1 to Z and remark out original Z then that new Z axis works so I know the driver is good. I am curious if the system thinks I only have 1 Z and therefor the others fail. And if so how to go about making it see the other Z axis.
@mietzekatzi
47 replies
RRCRat Rig Community [Unofficial]
•Created by Teckgeek on 7/10/2023 in #ratos-support
tmc5160 on a Octopus Max EZ
I've been through all the threads I found with the search and I cannot get X and Y 5160 working.
2 replies
RRCRat Rig Community [Unofficial]
•Created by Teckgeek on 6/19/2023 in #fix-my-printer
TMC SPI driver issue
Unable to write tmc spi 'stepper_x' register GLOBALSCALER Once the underlying issue is corrected, use the "FIRMWARE_RESTART" command to reset the firmware, reload the config, and restart the host software. Printer is shutdown
2 replies
RRCRat Rig Community [Unofficial]
•Created by Teckgeek on 3/29/2023 in #fix-my-resonance
Is this good?
3 replies
RRCRat Rig Community [Unofficial]
•Created by Teckgeek on 3/16/2023 in #fix-my-printer
Z-tilt working but bed wonky
Okay so I run z-tilt and it works fine corrects to .005 ish so klipper says. But you can look at the printer and see the bed is obviously skewed. In fact if I were to run a bed mesh toward the back left it would fail at the klicky probe triggers before it’s in position to probe. V-core 3.1 - 500 and it is consistent.everything measures fine.
3 replies
RRCRat Rig Community [Unofficial]
•Created by Teckgeek on 3/12/2023 in #fix-my-print
Move exceeds maximum extrusion
Where would I look to fix this error.
1:52 PM
Move exceeds maximum extrusion (1.416mm^2 vs 0.640mm^2)
1:52 PM
Move exceeds maximum extrusion (1.416mm^2 vs 0.640mm^2)
See the 'max_extrude_cross_section' config option for details
9 replies
RRCRat Rig Community [Unofficial]
•Created by Teckgeek on 3/12/2023 in #fix-my-mesh
Not sure what to adjust
12 replies