tcsjc
RRCRat Rig Community [Unofficial]
•Created by tcsjc on 12/7/2024 in #ratos-support
Ebb managed fan
ive got a 24v fan for part cooling but want to run it off of the ebb board. what lines do i need to add to user overrides?
5 replies
RRCRat Rig Community [Unofficial]
•Created by tcsjc on 12/4/2024 in #ratos-support
Board flashing error
I am trying to flash the octopus on my V3.1 and i keep getting
Octopus V1.1 detected but is unresponsive.
Klipper doesn't seem to be running on your board, which may indicate faulty firmware or a faulty board. Please check your board and try flashing it again.
trying to flash after doesnt work and i once saw the start of a script error in red
Any ideas what to try
50 replies
RRCRat Rig Community [Unofficial]
•Created by tcsjc on 11/5/2024 in #fix-my-mesh
Rear left dip ruining mesh
2 replies
RRCRat Rig Community [Unofficial]
•Created by tcsjc on 8/11/2024 in #ratos-support
check_gain_time
Anyone where in the config i can alter the check gain time, im using a lower power bed heater and need to increase the time from default, whatever that is
8 replies
RRCRat Rig Community [Unofficial]
•Created by tcsjc on 4/16/2024 in #ratos-support
weird error toolboard related
Has anyone had a random crash then ADC out of range? then
MCU 'toolboard' shutdown: Rescheduled timer in the past
This generally occurs when the micro-controller has been
requested to step at a rate higher than it is capable of
obtaining.
Once the underlying issue is corrected, use the
"FIRMWARE_RESTART" command to reset the firmware, reload the
config, and restart the host software.
Printer is shutdown
11 replies
RRCRat Rig Community [Unofficial]
•Created by tcsjc on 3/3/2024 in #fix-my-printer
Option 'control' in section 'extruder' must be specified??
Updated the OS recently and now i get this? Im using a btt ebb42 toolboard but maybe the config for all has changed?
3 replies
RRCRat Rig Community [Unofficial]
•Created by tcsjc on 2/21/2024 in #ratos-support
custom bed mesh
how do you configure a custom bed mesh szie ( i want to probe more points)
7 replies
RRCRat Rig Community [Unofficial]
•Created by tcsjc on 2/5/2024 in #fix-my-printer
VC3 500 with EBB42 ttc errors
Hi i continually at random points get timer too close errors on mcu toolboard. What could be the cause of this?
3 replies
RRCRat Rig Community [Unofficial]
•Created by tcsjc on 1/24/2024 in #fix-my-printer
Inability to maintain Hotend and bed temps VC3.1 500
My 3.1 500 runs fine for a good length of the print then randomly both the bed and hotend cant sustain temperatures despite rapidly increasing their PWM values. and the n i get an ADC error. Klippy log shows the increasing PWM and falling temps happen to both at the same time. Could this be a PSU failing?
13 replies
RRCRat Rig Community [Unofficial]
•Created by tcsjc on 1/24/2024 in #fix-my-mesh
V3.1 500 Mesh causing inconsistent print
Although i do a bed level and whether i get a fresh mesh each print or load the saved one my print is fine at the fron side of the bed but massively thins out at the rear end (first layer is pretty much see through!) what might be causing this?
13 replies
RRCRat Rig Community [Unofficial]
•Created by tcsjc on 12/2/2023 in #ratos-support
Bed leveling
2 queries, my z motors dont seem to be moving to the bed level. Is there a change to default loading of bed mesh? mine currently loads one saved ratos that i periodically update.
Secondly where do you configure how many probe points the bed mesh stores?
5 replies
RRCRat Rig Community [Unofficial]
•Created by tcsjc on 11/18/2023 in #ratos-support
webcam not working
I have a c310 webcam plugged in to my pi. I cannot get it to work! The device is definitely picked up by the pi according lsusb but have tried many configs in ratos to get it working and it won’t. It used to work in much older versions of ratos. Does anyone have any ideas?
5 replies
RRCRat Rig Community [Unofficial]
•Created by tcsjc on 11/13/2023 in #ratos-support
change wifi
Is there an easy way to change the wifi. My home network has changed and i need to change the wifi. Do i edit the ratos configurator section of wpa-supplicant or the default area?
6 replies
RRCRat Rig Community [Unofficial]
•Created by tcsjc on 5/2/2023 in #fix-my-mesh
What frame skew causes this mesh
10 replies
RRCRat Rig Community [Unofficial]
•Created by tcsjc on 4/15/2023 in #ratos-support
Cant see Ratos wifi
Hi I cant see the ratos wifi after a fresh install to configure it.
9 replies
RRCRat Rig Community [Unofficial]
•Created by tcsjc on 12/1/2022 in #fix-my-printer
vc3 rapido uhf issue
I have a rapido uhf on my vc3. I cannot calibrate the offset as it keeps saying move out of range. It’s over a few mm away after trying to calibrate
23 replies