Rubby
RRCRat Rig Community [Unofficial]
•Created by Rubby on 2/2/2025 in #fix-my-printer
Clicking during Y axis movement
I believe this was solved by doign the following:
6 replies
RRCRat Rig Community [Unofficial]
•Created by Rubby on 2/2/2025 in #fix-my-printer
Clicking during Y axis movement
I loosened off the Y on that side belt and turned the idlers on their own and it is certainly not the idlers so it is either the stepper or the bearing in the adapter plate? I guess replacing the bearing is the simplest option even though that's a decent amount of taking apart.
6 replies
RRCRat Rig Community [Unofficial]
•Created by Rubby on 2/2/2025 in #fix-my-printer
Clicking during Y axis movement
6 replies
RRCRat Rig Community [Unofficial]
•Created by Rubby on 1/7/2025 in #ratos-support
RatOS UpdateManager Invalid
4 replies
RRCRat Rig Community [Unofficial]
•Created by Rubby on 1/7/2025 in #ratos-support
RatOS UpdateManager Invalid
I don't want to try hard recovery as I imagine that will get rid of all of my configs? Although I am about to upgrade to IDEX so maybe that does not matter?
4 replies
RRCRat Rig Community [Unofficial]
•Created by Rubby on 11/22/2024 in #ratos-support
RatOS Heat Soak Macro Help
Hm I have seen the addition of time variables to the beacon macros but I'm not looking quite for that as I don't want to add time to the beginning of every print. Just hoping for a "heat up" macro to run at the start of the day to get things going as once it is hot there is no need to wait between prints as long as it does not cool off.
5 replies
RRCRat Rig Community [Unofficial]
•Created by Rubby on 11/22/2024 in #ratos-support
RatOS Heat Soak Macro Help
I guess I should also have a macro sets the temps back to 0 as well.
5 replies
RRCRat Rig Community [Unofficial]
•Created by SoftRock on 11/11/2024 in #fix-my-print
Nozzle is rattling against the print, making scrathing noise and producing top layer artifacts.
How does the first layer look? Feels like over extrusion could be to blame.
5 replies
RRCRat Rig Community [Unofficial]
•Created by Ferfi on 10/29/2024 in #ratos-support
Printer will not connect to WIFI all of sudden, creates RatOS hotspot instead
I have had the same issue with my pi. Unfortunately no solution I've just tried to avoid rebooting it so it stays connected to wifi. Someone said it is a known issue with Klipperscreen but I don't have a screen attached. Just adding my comment to hopefully bring more attention to the issue.
14 replies
RRCRat Rig Community [Unofficial]
•Created by Rubby on 10/29/2024 in #ratos-support
Inconsistent first layer between prints with Beacon
I realize that is not practical so what would be a practical solution? a "warm up" Macro for the start of the day to get things going?
20 replies
RRCRat Rig Community [Unofficial]
•Created by Rubby on 10/29/2024 in #ratos-support
Inconsistent first layer between prints with Beacon
20 replies
RRCRat Rig Community [Unofficial]
•Created by Rubby on 10/29/2024 in #ratos-support
Inconsistent first layer between prints with Beacon
20 replies
RRCRat Rig Community [Unofficial]
•Created by Rubby on 10/29/2024 in #ratos-support
Inconsistent first layer between prints with Beacon
20 replies
RRCRat Rig Community [Unofficial]
•Created by Rubby on 10/29/2024 in #ratos-support
Inconsistent first layer between prints with Beacon
Not sure how long I need to let it cool down but I will give it an hour or two and try with 1200 and 300 and let you know!
20 replies
RRCRat Rig Community [Unofficial]
•Created by Rubby on 10/29/2024 in #ratos-support
Inconsistent first layer between prints with Beacon
I am pretty sure I tried that the other day. I know I had 300 for hotend heat soak but I but I also had 300 for the bed heat soak time and the issue was the same. I can try it with 1200 and see. I will have to wait for everything to cool down though to verify the change
20 replies
RRCRat Rig Community [Unofficial]
•Created by Rubby on 10/29/2024 in #ratos-support
Inconsistent first layer between prints with Beacon
That is what I figured, which is why I let the bed heat for 15 minutes today before the first print but the issue still persisted? Maybe I need to heat the nozzle as well?
20 replies
RRCRat Rig Community [Unofficial]
•Created by Rubby on 10/29/2024 in #ratos-support
Inconsistent first layer between prints with Beacon
@Helge Keck Thanks for responding to my post in #beacon-contact Here is my issue with hopefully some more details. If you need any other information let me know.
20 replies
RRCRat Rig Community [Unofficial]
•Created by Rubby on 10/3/2024 in #ratos-support
RatOS fails to connect to WiFi on reboot
Hm I do not have a screen attached but could that still be affecting it? Any way to disable klipperscreen if that is the case?
19 replies
RRCRat Rig Community [Unofficial]
•Created by Raym.i on 10/17/2024 in #fix-my-print
Overextrusion
Also what does the first layer alone look like? It's possible it is not an extrusion issue but maybe you Z is not going up a full layer at a time which would cause excess squish as well
12 replies
RRCRat Rig Community [Unofficial]
•Created by Raym.i on 10/17/2024 in #fix-my-print
Overextrusion
Does it look this way on normal prints as well or only when doing this extrusion test?
12 replies