sherbs
RRCRat Rig Community [Unofficial]
•Created by sherbs on 4/23/2025 in #ratos-support
update to 2.1 RC3 gives configuration error: 'allow_unknown_gcode_generator' is not valid

38 replies
RRCRat Rig Community [Unofficial]
•Created by sherbs on 4/16/2025 in #fix-my-printer
extrusion differences between near identical printers
Hi Folks,
I have two vcore 300 printers. One is vcore3.0, the other vcore3.1. Both printers have very much the same hardware - octopus pro, rapido 2 uhf, orbiter 2, same TC 0.4 nozzles from West 3D.
The 3.1 noticeably underextrudes as compared to the other when running the same gcode and same roll of plastic. I'd always expect slight differences between printers - but the difference in this case is quite noticeable on top surfaces and I need to find some way to address it.
Two questions:
1) Any suggestions as to why this might be the case? they are running different builds of 2.0.2 RatOS - could that be an issue?
2) any suggestions on how to work around this issue? I can bump up the extrusion factor in mainsail but that doesn't seem to be permanent. Is there an option in printer.cfg that might help?
Ideally I want to be able to push gcode from my slicer to either printer and not have to worry about targeting gcode to a specific printer.
6 replies
RRCRat Rig Community [Unofficial]
•Created by sherbs on 8/8/2023 in #fix-my-print
Help with slicer

1 replies
RRCRat Rig Community [Unofficial]
•Created by sherbs on 3/30/2023 in #fix-my-printer
X/Y dimensional accuracy
Hi Folks,
Trying to identify options for improving the dimensional accuracy of printed parts on my vc3.0.
I'm printing some test squares and finding the following:
modeled x-y vs actual x-y
20 x 10 -> 19.89 x 9.93
30 x 10 -> 29.83 x 9.95
50 x 10 -> 49.73 x 9.93
80 x 10 -> 79.66 x 9.93
40 x 40 -> 39.70 x 39.71
Short of scaling every part in x & y in the slicer, is there a more universal fix that can be applied? Thinking about tweaking stepper rotation_distance for x & y steppers but want to open some discussion on it to see what others think might be a solution.
I have another printer that results in much more accurate sizes without scaling in the slicer so I feel like this can be done, just not sure what the right approach would be.
11 replies
RRCRat Rig Community [Unofficial]
•Created by sherbs on 12/27/2022 in #fix-my-printer
Mid-print, mcu lost
Hi folks,
I've had this error repeat twice in a row now. Mid-print I'm getting a 'lost communication to MCU' error. No other information is available in the interface.
I can get a console on the pi. Wondering what debugging steps I can take to track down the specific cause.
Are there log files I can look at? Would you suspect the board or something else?
The only thing thus far that seems to resolve the issue is power cycling the printer.
Thanks for any help!
3 replies
RRCRat Rig Community [Unofficial]
•Created by sherbs on 12/19/2022 in #fix-my-printer
Rapido repair
Hi folks, has anyone successfully repaired a rapido hot end with an intermittent thermistor connectivity issue? Wondering if possible or if it's advised to just replace the whole core.
Thanks!
12 replies
RRCRat Rig Community [Unofficial]
•Created by sherbs on 12/12/2022 in #fix-my-printer
Phaetus rapido sudden temp plunge

7 replies