MACBEAN
RRCRat Rig Community [Unofficial]
•Created by MACBEAN on 11/5/2024 in #fix-my-print
Layers not sticking past layer 3
6 replies
RRCRat Rig Community [Unofficial]
•Created by MACBEAN on 10/4/2024 in #fix-my-mesh
vcore 4 500 hybrid looks all over the place
12 replies
RRCRat Rig Community [Unofficial]
•Created by MACBEAN on 4/9/2024 in #ratos-support
Setting up adaptive mesh
Saw that i could do an adaptive mesh to avoid probing a whole 500 bed every print but it doesn't work.
do i need to set 'variable_calibrate_bed_mesh: False' to True? is this what's causing my printer to ignore the variable_adaptive_mesh: True ?
read my prusaslicer Gcode and it is spitting out dimensions
6 replies
RRCRat Rig Community [Unofficial]
•Created by MACBEAN on 3/31/2024 in #fix-my-print
What is making my corners look like this?
5 replies
RRCRat Rig Community [Unofficial]
•Created by MACBEAN on 3/23/2024 in #fix-my-print
What could be causing this kind of underextrusiom
2 replies
RRCRat Rig Community [Unofficial]
•Created by MACBEAN on 8/20/2023 in #fix-my-print
Retraction calibration help
6 replies
RRCRat Rig Community [Unofficial]
•Created by MACBEAN on 8/17/2023 in #fix-my-resonance
help interpreting my belt tension graphs
7 replies
RRCRat Rig Community [Unofficial]
•Created by MACBEAN on 6/3/2023 in #fix-my-printer
Is my rail eating itself?
3 replies
RRCRat Rig Community [Unofficial]
•Created by MACBEAN on 5/21/2023 in #fix-my-print
Layer shift looking like one motor skipped or slipped
1 replies
RRCRat Rig Community [Unofficial]
•Created by MACBEAN on 5/14/2023 in #fix-my-print
Bridging over infill destroying prints
32 replies
RRCRat Rig Community [Unofficial]
•Created by MACBEAN on 4/24/2023 in #fix-my-printer
Z-offset seems to be wrong every time
setting the z offset using the probe_calibrate command using the paper method seems to be ignored whenever I start a print requiring me to change it with the offset buttons until it is either not scraping or is actually laying on the bed, any ideas?
23 replies
RRCRat Rig Community [Unofficial]
•Created by MACBEAN on 4/13/2023 in #fix-my-printer
Extruder heater not heating at expected rate
16 replies
RRCRat Rig Community [Unofficial]
•Created by MACBEAN on 4/12/2023 in #ratos-support
start macros
How do I modify my start macros to load a bed mesh instead of creating a new one at the start of every print? and the same goes with not doing a z tilt
12 replies
RRCRat Rig Community [Unofficial]
•Created by MACBEAN on 4/11/2023 in #fix-my-mesh
Creating a bed mesh
feels like a stupid question buy how do I create a bed mesh? I cant open the heightmap tab in mainsail
7 replies
RRCRat Rig Community [Unofficial]
•Created by MACBEAN on 4/9/2023 in #fix-my-printer
Pi keeps dropping wifi and sometimes doesn't connect on boot
As in the title
21 replies
RRCRat Rig Community [Unofficial]
•Created by MACBEAN on 4/9/2023 in #fix-my-printer
Part cooling fan running full speed at 0% and homing issues
I have the delta PWM fan set up as close as I can tell to what douzuki says in their build instructions but when set to 0% it appears to be running at 100% and vice versa
secondly, im unable to home as y goes in the wrong direction, and when reversed goes all the way back and then and doesnt stop on the endstop and continues to drive left
9 replies