Jeb Bush
RRCRat Rig Community [Unofficial]
•Created by Jeb Bush on 2/3/2025 in #fix-my-resonance
First Time Doing Belt Tuning... Looking For Guidance
Probably related to these vibrations
19 replies
RRCRat Rig Community [Unofficial]
•Created by Jeb Bush on 2/3/2025 in #fix-my-resonance
First Time Doing Belt Tuning... Looking For Guidance
Yeah I need to dive into that a bit more. I’ve been chasing other gremlins like crappy usb c connectors coming loose during a 2 day print
19 replies
RRCRat Rig Community [Unofficial]
•Created by Jeb Bush on 2/3/2025 in #fix-my-resonance
First Time Doing Belt Tuning... Looking For Guidance
yeah i have the filament sensor and have filament installed so i dont think thats it. The rattling seems to be coming from lower like the hot end or carriage but i still need to poke around a bit more
19 replies
RRCRat Rig Community [Unofficial]
•Created by Jeb Bush on 2/3/2025 in #fix-my-resonance
First Time Doing Belt Tuning... Looking For Guidance
Maybe. I haven’t dug into it further yet
19 replies
RRCRat Rig Community [Unofficial]
•Created by Jeb Bush on 2/3/2025 in #fix-my-resonance
First Time Doing Belt Tuning... Looking For Guidance
ok so i think belts are OK as far as tension but i definitely neglected to check on length so I'm guessing thats the issues with the differences at 92ish Hz and 130ish hz. i think I have some issue with my toolhead causing the peak at 50Hz because I hear something gross rattling around in it at that part of the test.
19 replies
RRCRat Rig Community [Unofficial]
•Created by Numb3r_0ne on 1/28/2025 in #ratos-support
beacon 3.1 wrong offset
I think I'm having the same issue with my setup as well (without using the overrides above)
6 replies
RRCRat Rig Community [Unofficial]
•Created by Jeb Bush on 1/27/2025 in #ratos-support
Probe Samples Exceed Tolerance
brute force tried it 5 times and it worked finally
10 replies
RRCRat Rig Community [Unofficial]
•Created by Jeb Bush on 1/27/2025 in #ratos-support
Probe Samples Exceed Tolerance
ok i guess i was just being dumb
10 replies
RRCRat Rig Community [Unofficial]
•Created by Jeb Bush on 1/27/2025 in #ratos-support
Probe Samples Exceed Tolerance
10 replies
RRCRat Rig Community [Unofficial]
•Created by Jeb Bush on 1/27/2025 in #ratos-support
Probe Samples Exceed Tolerance
I would think the bent lead screw would be consistent at least and would just cause print issues but maybe thats misunderstood
10 replies
RRCRat Rig Community [Unofficial]
•Created by Jeb Bush on 1/27/2025 in #ratos-support
Probe Samples Exceed Tolerance
Yeah I’ll give it a shot. Only other thing from the list you gave would be some not so straight z screws. I bought this used and it’s on my list of things to fix but hoped it wouldn’t be a big deal
10 replies
RRCRat Rig Community [Unofficial]
•Created by Jeb Bush on 1/27/2025 in #ratos-support
Probe Samples Exceed Tolerance
I checked everything and am repeating. Seems like the measurements are drifting a bit. Wondering if the nozzle temp is still settling and the metal expanding a bit
10 replies
RRCRat Rig Community [Unofficial]
•Created by Demdor on 1/25/2025 in #fix-my-printer
vcore 3.1 prints fine with prints that are up to 3 hours But with longer prints 5+ it layershifts
Over temp?
102 replies
RRCRat Rig Community [Unofficial]
•Created by Demdor on 1/25/2025 in #fix-my-printer
vcore 3.1 prints fine with prints that are up to 3 hours But with longer prints 5+ it layershifts
Well that link above will get you what you need. I also wouldn’t bother wiring up the tacho
102 replies
RRCRat Rig Community [Unofficial]
•Created by Demdor on 1/25/2025 in #fix-my-printer
vcore 3.1 prints fine with prints that are up to 3 hours But with longer prints 5+ it layershifts
Ah
102 replies
RRCRat Rig Community [Unofficial]
•Created by Demdor on 1/25/2025 in #fix-my-printer
vcore 3.1 prints fine with prints that are up to 3 hours But with longer prints 5+ it layershifts
I don’t think it offers any benefit for that application over a 2 wire fan
102 replies
RRCRat Rig Community [Unofficial]
•Created by Demdor on 1/25/2025 in #fix-my-printer
vcore 3.1 prints fine with prints that are up to 3 hours But with longer prints 5+ it layershifts
102 replies
RRCRat Rig Community [Unofficial]
•Created by Demdor on 1/25/2025 in #fix-my-printer
vcore 3.1 prints fine with prints that are up to 3 hours But with longer prints 5+ it layershifts
Are you running an octopus?
102 replies
RRCRat Rig Community [Unofficial]
•Created by Jeb Bush on 1/10/2025 in #fix-my-printer
Rapido 1 Reading Lower Than Expected Temperature
31 replies
RRCRat Rig Community [Unofficial]
•Created by Jeb Bush on 1/10/2025 in #fix-my-printer
Rapido 1 Reading Lower Than Expected Temperature
Also, here’s the link to mellows klipper config recommendations so that you don’t have to go hunt for where that screenshot is from
31 replies