PollePro
RRCRat Rig Community [Unofficial]
•Created by PollePro on 9/12/2023 in #fix-my-printer
BIQU Microprobe
Yea from what i could see it it should be the same wiring but no.. 😛
12 replies
RRCRat Rig Community [Unofficial]
•Created by PollePro on 9/12/2023 in #fix-my-printer
BIQU Microprobe
No i bought a new BLTouch :/
12 replies
RRCRat Rig Community [Unofficial]
•Created by PollePro on 9/12/2023 in #fix-my-printer
BIQU Microprobe
Seems like the same as BLTouch? I use a Octopus Pro f446
12 replies
RRCRat Rig Community [Unofficial]
•Created by PollePro on 9/12/2023 in #fix-my-printer
BIQU Microprobe
12 replies
RRCRat Rig Community [Unofficial]
•Created by Naiofz91 on 9/2/2023 in #fix-my-printer
" Endstop z still triggered after retract "
Hmm okay 🙂
9 replies
RRCRat Rig Community [Unofficial]
•Created by PollePro on 9/12/2023 in #fix-my-printer
BIQU Microprobe
Just cant seem to find the error. From what i can find the wiring from BLTouch and BIQU Microprobe should be the same?
12 replies
RRCRat Rig Community [Unofficial]
•Created by Naiofz91 on 9/2/2023 in #fix-my-printer
" Endstop z still triggered after retract "
Did u find a fix?
9 replies
RRCRat Rig Community [Unofficial]
•Created by adverse-sapphire on 9/7/2023 in #fix-my-print
fuzzy skin
Looks like its too close to the bed
12 replies
RRCRat Rig Community [Unofficial]
•Created by absent-sapphire on 9/7/2023 in #fix-my-print
fuzzy skin
What temp?
12 replies
RRCRat Rig Community [Unofficial]
•Created by DanO on 8/24/2023 in #fix-my-print
ASA multi part fails (singles print fine)
I know, Thats why i ask him if he use glue and what kind 🙂
27 replies
RRCRat Rig Community [Unofficial]
•Created by DanO on 8/24/2023 in #fix-my-print
ASA multi part fails (singles print fine)
It just looks like there is some glue on the picture 🙂
27 replies
RRCRat Rig Community [Unofficial]
•Created by DanO on 8/24/2023 in #fix-my-print
ASA multi part fails (singles print fine)
Do u use any kind of adhisiv glue?
27 replies
RRCRat Rig Community [Unofficial]
•Created by DanO on 8/24/2023 in #fix-my-print
ASA multi part fails (singles print fine)
Temp on bed? retraction? Nozzle temp?
27 replies
RRCRat Rig Community [Unofficial]
•Created by Sky217 on 8/17/2023 in #ratos-support
Camera not working 😖
5 replies
RRCRat Rig Community [Unofficial]
•Created by Sky217 on 8/17/2023 in #ratos-support
Camera not working 😖
My settings look like this: [cam 1]
mode: camera-streamer # ustreamer - Provides mjpg and snapshots. (All devices)
# camera-streamer - Provides webrtc, mjpg and snapshots. (rpi + Raspi OS based only)
enable_rtsp: true # If camera-streamer is used, this enables also usage of an rtsp server
rtsp_port: 8554 # Set different ports for each device!
port: 8080 # HTTP/MJPG Stream/Snapshot Port
device: /base/soc/i2c0mux/i2c@1/imx219@10 # See Log for available ...
resolution: 1280x720 # widthxheight format
max_fps: 30 # If Hardware Supports this it will be forced, otherwise ignored/coerced.
5 replies
RRCRat Rig Community [Unofficial]
•Created by national-gold on 12/26/2022 in #fix-my-printer
ADXL problem?
Did u find a fix for this problem?
3 replies
RRCRat Rig Community [Unofficial]
•Created by Mr.Robot on 6/26/2023 in #ratos-support
AWD TMC 5160 issue
Will have to do that aswell then 😛
88 replies
RRCRat Rig Community [Unofficial]
•Created by Mr.Robot on 6/26/2023 in #ratos-support
AWD TMC 5160 issue
So put ! where there is non and remove ! where they are?
88 replies
RRCRat Rig Community [Unofficial]
•Created by Mr.Robot on 6/26/2023 in #ratos-support
AWD TMC 5160 issue
Yea, Thats also were i got too 😛
88 replies
RRCRat Rig Community [Unofficial]
•Created by Mr.Robot on 6/26/2023 in #ratos-support
AWD TMC 5160 issue
make sure your motors run the right way 😛
88 replies