mavi - ilezirabbit
RRCRat Rig Community [Unofficial]
•Created by mavi - ilezirabbit on 9/25/2024 in #fix-my-print
Sensor Equivalent
I have a "Ratig Vcore3.1 500" printer that I built with my own means. I am using Bltouch on this machine, but I am having problems. That's why I want to use the "Rat Rig "SuperPinda" probe by Pepperl & Fuchs (Inductive 5VDC Sensor)" sensor used in the original. However, this product is not available in the country I live in, Turkey, and the process of bringing products from abroad is very difficult for me. So can I use the product whose link I left below instead of this product? Is this the exact same product?
https://www.pepperl-fuchs.com/turkey/tr/classid_143.htm?view=productdetails&prodid=106674#overview
Inductive sensor NBN2,5-8GM35-E1L-Y
22 replies
RRCRat Rig Community [Unofficial]
•Created by mavi - ilezirabbit on 5/24/2024 in #fix-my-mesh
my mesh is bad...
3 replies
RRCRat Rig Community [Unofficial]
•Created by mavi - ilezirabbit on 5/23/2024 in #fix-my-mesh
First Layer Problem with Adaptive_Mesh
2 replies
RRCRat Rig Community [Unofficial]
•Created by mavi - ilezirabbit on 5/21/2024 in #fix-my-printer
First Layer Problem With Adaptive_Mesh
Hello. When I use adaptive mesh, I have problems with the first layer. But don't use it, I don't have any problems when I use normal bed_mesh. Something caught my attention, I think maybe this is the reason. As you can see in the screenshot, no matter which part I print, "PROBE_FOR_PRIMING: Probing the prime location at X: 493.0 Y: 33.0" always takes measurements from this point before meshing. Why does it always measure from X: 493.0 Y: 33.0?
2 replies
RRCRat Rig Community [Unofficial]
•Created by mavi - ilezirabbit on 5/13/2024 in #fix-my-print
Stringing Isue
5 replies
RRCRat Rig Community [Unofficial]
•Created by mavi - ilezirabbit on 4/4/2024 in #fix-my-printer
My prints are interrupted.
Hello. My printing has been interrupted for the last few days. The clipper connection is also working. When I reconnect, it says "interrupted" on the track I last sent to print. I examined the log files and there is no information. I couldn't find out what could be causing this.
I also want to say this for extra information. Since the first day I built the printer, there has been a warning in clipper notifications that the voltage has fallen below 4.65 volts. but this has never been a problem before.
25 replies
RRCRat Rig Community [Unofficial]
•Created by mavi - ilezirabbit on 3/7/2024 in #ratos-support
ratrig V3.1 500 for probe chose.
Hello. Do you think I can use the sensor whose product link I gave below for my Ratrig v3.1 500 printer? Can you give me information about this? "https://www.leuze.com/tr-tr/is-108-mm2nc-4n0-m83/50129919"
5 replies
RRCRat Rig Community [Unofficial]
•Created by mavi - ilezirabbit on 3/1/2024 in #ratos-support
variable_adaptive_mesh fault with Bl-Touch
Hello. I want to use the "variable_adaptive_mesh" setting. I have a vcore v3.1 500 encloser printer and it has BL-Touch on it. The accuracy result of my BL-Touch is as follows: "probe accuracy results: maximum 1.860625, minimum 1.787187, range 0.073438, average 1.824437, median 1.825000, standard deviation 0.024391"
I organized all my files. I leave my cfg file below, you can check it out.
When I start printing, after making the adaptive mesh, I get this error when printing starts and I couldn't find the reason for it. Can you help me?
ERROR: "Error evaluating 'gcode_macro ADD_PRIME_PROBE_TO_OFFSET:gcode': gcode.CommandError: Abnormal probe offset detected. Needed offset of {adjustment} is below the offset threshold of -1mm. Please verify the probe is over the bed when probing for priming. If it isn't, you should adjust you min/max bed_mesh settings so the probe is always over the print area."
4 replies
RRCRat Rig Community [Unofficial]
•Created by mavi - ilezirabbit on 3/1/2024 in #fix-my-printer
variable_adaptive_mesh Problem with BL-Touch
Hello. I want to use the "variable_adaptive_mesh" setting. I have a vcore v3.1 500 encloser printer and it has BL-Touch on it. The accuracy result of my BL-Touch is as follows: "probe accuracy results: maximum 1.860625, minimum 1.787187, range 0.073438, average 1.824437, median 1.825000, standard deviation 0.024391"
I organized all my files. I leave my cfg file below, you can check it out.
When I start printing, after making the adaptive mesh, I get this error when printing starts and I couldn't find the reason for it. Can you help me?
ERROR: "Error evaluating 'gcode_macro ADD_PRIME_PROBE_TO_OFFSET:gcode': gcode.CommandError: Abnormal probe offset detected. Needed offset of {adjustment} is below the offset threshold of -1mm. Please verify the probe is over the bed when probing for priming. If it isn't, you should adjust you min/max bed_mesh settings so the probe is always over the print area."
60 replies