jason974
RRCRat Rig Community [Unofficial]
•Created by jason974 on 1/3/2024 in #ratos-support
Memory leak, high memory use shutting down klipper
Alfrix on Github gave me this answer : "The error messages generate pop-ups and it consumes a lot of processing only to do that", so to avoid the problem dont have error messages ...............
34 replies
RRCRat Rig Community [Unofficial]
•Created by jason974 on 1/3/2024 in #ratos-support
Memory leak, high memory use shutting down klipper
i've submitted a BUG report on Github, but i think i found the culprit
I've sliced with an old profile with ARC enabled in the slicer but not in printer.cfg, and i keep getting "error unknown command G17" (or G3) messages, and i think it saturates the service....but that's strange anyway.
34 replies
RRCRat Rig Community [Unofficial]
•Created by jason974 on 1/3/2024 in #ratos-support
Memory leak, high memory use shutting down klipper
tnx a lot for the help
34 replies
RRCRat Rig Community [Unofficial]
•Created by jason974 on 1/3/2024 in #ratos-support
Memory leak, high memory use shutting down klipper
i have a 2nd screen, the same model, i'll connect it to see if it's the same (with service enabled of course)
34 replies
RRCRat Rig Community [Unofficial]
•Created by jason974 on 1/3/2024 in #ratos-support
Memory leak, high memory use shutting down klipper
34 replies
RRCRat Rig Community [Unofficial]
•Created by jason974 on 1/3/2024 in #ratos-support
Memory leak, high memory use shutting down klipper
should i disconnect it and see what happens ??
34 replies
RRCRat Rig Community [Unofficial]
•Created by jason974 on 1/3/2024 in #ratos-support
Memory leak, high memory use shutting down klipper
i can always use the web interface, no problem if temporary
34 replies
RRCRat Rig Community [Unofficial]
•Created by jason974 on 1/3/2024 in #ratos-support
Memory leak, high memory use shutting down klipper
it's very alggy since i updated to V2.02
34 replies
RRCRat Rig Community [Unofficial]
•Created by jason974 on 1/3/2024 in #ratos-support
Memory leak, high memory use shutting down klipper
yes, the BTT 7"
34 replies
RRCRat Rig Community [Unofficial]
•Created by jason974 on 1/3/2024 in #ratos-support
Memory leak, high memory use shutting down klipper
34 replies
RRCRat Rig Community [Unofficial]
•Created by jason974 on 1/3/2024 in #ratos-support
Memory leak, high memory use shutting down klipper
34 replies
RRCRat Rig Community [Unofficial]
•Created by jason974 on 1/3/2024 in #ratos-support
Memory leak, high memory use shutting down klipper
34 replies
RRCRat Rig Community [Unofficial]
•Created by jason974 on 1/3/2024 in #ratos-support
Memory leak, high memory use shutting down klipper
yes, and the full update did not solve the problem.
i did a "top -c" in SSH, and it seems klipperscreen is the cuprit.
34 replies
RRCRat Rig Community [Unofficial]
•Created by jason974 on 1/3/2024 in #ratos-support
Memory leak, high memory use shutting down klipper
I've done a full update, and i dont like doing that knowing i've already did a fresh install like 3 weeks ago, but the problem seems gone.......
34 replies
RRCRat Rig Community [Unofficial]
•Created by jason974 on 6/17/2023 in #ratos-support
Adaptive meshing, printing outside of "meshed" area
well, it happened after moving it by car to a friend's place and you ere right, the gantry was not square to the front frame anymore......one side of the gantry was touching before the other.
removed the belts, loosened all the screws and realigned it, now it does what it's asked for
Tnx for the tip !!
4 replies
RRCRat Rig Community [Unofficial]
•Created by genetic-orange on 2/25/2023 in #fix-my-print
Calibration print with 0.6mm nozzle
could be the PA value as well
8 replies
RRCRat Rig Community [Unofficial]
•Created by extended-salmon on 2/25/2023 in #fix-my-print
Calibration print with 0.6mm nozzle
more people using SuSlic3r here than BBS.....hard to tell
8 replies
RRCRat Rig Community [Unofficial]
•Created by ugly-tan on 2/21/2023 in #fix-my-printer
Lubricating the linear rails with 3 in 1 oil
10 replies
RRCRat Rig Community [Unofficial]
•Created by useful-bronze on 2/21/2023 in #fix-my-mesh
500mm v-core 3 (enclosed). Can I do better?
i added a chamber probe temp and i only start printing after it reached at least 45°C
14 replies
RRCRat Rig Community [Unofficial]
•Created by xenogeneic-maroon on 2/21/2023 in #fix-my-mesh
500mm v-core 3 (enclosed). Can I do better?
and always heatsoak the printer before printing
14 replies