Godzilla_Bill_K4IBC
RRCRat Rig Community [Unofficial]
•Created by NickiDotDk on 11/2/2024 in #fix-my-resonance
Orbitool Accelorometer vs Beacon Accelorometer
Is the umbilical rubbing or hitting the top or sides?
6 replies
RRCRat Rig Community [Unofficial]
•Created by NickiDotDk on 11/2/2024 in #fix-my-resonance
Orbitool Accelorometer vs Beacon Accelorometer
Check to make sure the toolboard is tight and the mount for the toolboard. The EBB42 has proven to be better than the Beacon because of better location.
6 replies
RRCRat Rig Community [Unofficial]
•Created by tg73 on 10/8/2024 in #fix-my-print
Regular surface distortion pattern towards end of larger first layers VC4
I have used Torlon 4301 bearing grade for sliding loads before.
1745 replies
RRCRat Rig Community [Unofficial]
•Created by tg73 on 10/8/2024 in #fix-my-print
Regular surface distortion pattern towards end of larger first layers VC4
Yes
1745 replies
RRCRat Rig Community [Unofficial]
•Created by tg73 on 10/8/2024 in #fix-my-print
Regular surface distortion pattern towards end of larger first layers VC4
PTFE sliders
1745 replies
RRCRat Rig Community [Unofficial]
•Created by tg73 on 10/8/2024 in #fix-my-print
Regular surface distortion pattern towards end of larger first layers VC4
Sorry I didn't get a chance to respond yesterday. My thought is why not let everything kind of float and be able to move in the X direction. Extrusion could move in X direction between joiners. The joiners must remain tight at the Y carriages but allow the extrusion to slip in X direction. But it should remain restrained in Y direction. Then allow the rail to float on the extrusion in the X direction but be restrained in the Y direction. I am not talking about being loosey goosey as you would effect Z if they were. We know the expansion is a given and is different for the extrusion and the rail so why not let them expand and float like a bridge does in summer and winter?
1745 replies
RRCRat Rig Community [Unofficial]
•Created by Arthur_C on 10/12/2024 in #ratos-support
Move exceeds maximum extrusion (at primeblob)
44 replies
RRCRat Rig Community [Unofficial]
•Created by tg73 on 10/8/2024 in #fix-my-print
Regular surface distortion pattern towards end of larger first layers VC4
OverNight air
1745 replies
RRCRat Rig Community [Unofficial]
•Created by tg73 on 10/8/2024 in #fix-my-print
Regular surface distortion pattern towards end of larger first layers VC4
If they are doughnut holes I will take them. Send them DHL please.
1745 replies
RRCRat Rig Community [Unofficial]
•Created by tg73 on 10/8/2024 in #fix-my-print
Regular surface distortion pattern towards end of larger first layers VC4
How about trying 3 screws one at each end and one in the middle torque 0.5Nm
1745 replies
RRCRat Rig Community [Unofficial]
•Created by Rewire on 10/4/2024 in #ratos-support
still cant get first layers to be consistent
Disconnect the control wire going to the SSR will always disable the SSR.
710 replies
RRCRat Rig Community [Unofficial]
•Created by 03Julian04 on 9/24/2024 in #ratos-support
first layer issues
I feel edjamacated now
923 replies
RRCRat Rig Community [Unofficial]
•Created by 03Julian04 on 9/24/2024 in #ratos-support
first layer issues
Yes that is what I meant.
923 replies
RRCRat Rig Community [Unofficial]
•Created by 03Julian04 on 9/24/2024 in #ratos-support
first layer issues
So basically a little more tuning to balance out the variance front to back and the wriggles?
923 replies
RRCRat Rig Community [Unofficial]
•Created by 03Julian04 on 9/24/2024 in #ratos-support
first layer issues
Sorry maybe it is my old eyes but when I open that image in browser and fullsize it, it doesn't look perfect. It looks better but not perfect. Am I being too critical and asking too much?
923 replies
RRCRat Rig Community [Unofficial]
•Created by millenford - VC4 300h on 9/5/2024 in #ratos-support
Would an SSD (vs the SD card) speed up full updates on RPi 4B?
Was RPi able to see it easily.
44 replies
RRCRat Rig Community [Unofficial]
•Created by armearme. on 9/16/2024 in #ratos-support
RatOS initial setup and configuration
As soon as you flash everything do an update. There has been some updates pushed that will elminate the errors. Don't try to fix them manually in the software.
179 replies
RRCRat Rig Community [Unofficial]
•Created by millenford - VC4 300h on 9/5/2024 in #ratos-support
Would an SSD (vs the SD card) speed up full updates on RPi 4B?
This is the USB 3.0 SSD I got from a recommendation from another user from here. Haven't had a chance to test them yet. I don't doubt they will work.
https://www.aliexpress.us/item/2251832734017445.html
44 replies
RRCRat Rig Community [Unofficial]
•Created by Oldschoolhippie on 9/23/2024 in #ratos-support
ADC out of range
Are you sure you selcted PT1000 in config
55 replies