wolfnacht
RRCRat Rig Community [Unofficial]
•Created by YouvBeenThumped on 3/30/2024 in #fix-my-printer
Belt tension or something else?
Pending the distance of the Pi from your board, I pull the 5v directly from my Octopus and haven't had an issue with undervoltage since. If you go this route, make sure you use both 5v outputs and 2 grounds.
10 replies
RRCRat Rig Community [Unofficial]
•Created by wolfnacht on 9/26/2023 in #fix-my-print
"Ripple" on bottom and top layers
Oooo never thought of that, mine is definitely heavy that's for sure. I'm looking at running x/y chains for mine and the only thing "free" will be the Bowden tube.
Currently getting parts together to repair mine... my failure is worse than I thought...
15 replies
RRCRat Rig Community [Unofficial]
•Created by wolfnacht on 9/26/2023 in #fix-my-print
"Ripple" on bottom and top layers
I'll check it out. I had a major printer failure and I'm running off a new EVA lol. 🙃
15 replies
RRCRat Rig Community [Unofficial]
•Created by QUINX on 10/4/2023 in #ratos-support
Ethernet Static IP with M8P/CB1
if your router supports setting a static lease, that'd be the best way
you SHOULD be able to SSH into the CB1 and edit the file in /etc/network/interfaces
3 replies
RRCRat Rig Community [Unofficial]
•Created by wolfnacht on 9/28/2023 in #ratos-support
Multiple printers, one RatOS installation
i searched around I didnt find anything on it, I'll look again.
3 replies
RRCRat Rig Community [Unofficial]
•Created by Steef on 9/26/2023 in #fix-my-resonance
Belt tension check
Here's the tool I found someone posted a few days ago I was talking about.
https://www.printables.com/model/151815-belt-tensioner-meter-9-mm-petg-prusament
18 replies
RRCRat Rig Community [Unofficial]
•Created by Steef on 9/26/2023 in #fix-my-resonance
Belt tension check
I found this file on here a while ago, and its how I adjusted my belts, and haven had any issues with the belts.
someone posted a tool from printables in general as well I'll see if I can find it for ya.
18 replies
RRCRat Rig Community [Unofficial]
•Created by wolfnacht on 9/26/2023 in #fix-my-print
"Ripple" on bottom and top layers
15 replies
RRCRat Rig Community [Unofficial]
•Created by wolfnacht on 9/26/2023 in #fix-my-print
"Ripple" on bottom and top layers
15 replies
RRCRat Rig Community [Unofficial]
•Created by wolfnacht on 9/26/2023 in #fix-my-print
"Ripple" on bottom and top layers
a bit being about 0.05-0.075 (dont remember exactly)
15 replies
RRCRat Rig Community [Unofficial]
•Created by wolfnacht on 9/26/2023 in #fix-my-print
"Ripple" on bottom and top layers
I'll run a full mesh here shortly, print finally finished up, I've been using the built in adaptive mesh.
15 replies
RRCRat Rig Community [Unofficial]
•Created by wolfnacht on 9/26/2023 in #fix-my-print
"Ripple" on bottom and top layers
I thought the ratrig build plate was double sided, the adhesion issue makes ALOT more sense then. I managed to destroy the textured side, and a nozzle, so I'm on the smooth side till I get a new textured plate.
15 replies
RRCRat Rig Community [Unofficial]
•Created by wolfnacht on 9/26/2023 in #fix-my-print
"Ripple" on bottom and top layers
during the first layer I tried backing it off a bit, I didn't show any improvement, I'll throw on a test print after this one finishes.
the smooth side of this PEI sheet has been a bit of a nightmare for me. PETG didnt want to stick at all, until I slapped some hairspray down. Considering the horror stories I've hear with PEI and PETG, I guess I should feel lucky.
15 replies
RRCRat Rig Community [Unofficial]
•Created by rival-black on 9/20/2023 in #fix-my-printer
raspberry power
What are you using to power at the GPIO currently?
12 replies
RRCRat Rig Community [Unofficial]
•Created by frail-apricot on 9/20/2023 in #fix-my-printer
raspberry power
I can't vouch for that, I'll attempt again on my rewire, but I couldn't get it to work personally, Hence why I opted for the 5V rail from the board itself. Supposedly, the board supports 5A on the 5V rail, so it shouldn't have an issue pushing the 3A over USB, I planned on poking at it again when I go to rewire the electonrics. Hoping I can 100% confirm/Deny
12 replies
RRCRat Rig Community [Unofficial]
•Created by graceful-blue on 9/20/2023 in #fix-my-printer
raspberry power
I think he was refering to powering the Pi from the USB-C Port on the Octo to the USB-C port on the Pi, I've heard of it being done. I havent had any luck with it.
Atleast thats how I understood the question.
I do believe the 4 supports OTG on the USB-C.
12 replies
RRCRat Rig Community [Unofficial]
•Created by ItsJesus on 9/11/2023 in #fix-my-printer
Delta 4 pin fan not working
Following the pinout for the skrat
6 replies
RRCRat Rig Community [Unofficial]
•Created by ItsJesus on 9/11/2023 in #fix-my-printer
Delta 4 pin fan not working
Have you tried this?
https://os.ratrig.com/docs/guides/4028
6 replies
RRCRat Rig Community [Unofficial]
•Created by exotic-emerald on 9/20/2023 in #fix-my-printer
raspberry power
I've heard that people have successfully powered the PI via the USBC port, something about enabling OTG in the boot.txt, I have NOT been successful, however I AM directly powering my PI off the 5V UART header on the octopus to the 5V GPIO.
12 replies