omerk83
RRCRat Rig Community [Unofficial]
•Created by omerk83 on 4/6/2025 in #fix-my-print
Purge blobs in the middle of a print
BTW beautiful printer 😍
23 replies
RRCRat Rig Community [Unofficial]
•Created by omerk83 on 4/6/2025 in #fix-my-print
Purge blobs in the middle of a print
I'll give it a shot, thanks
23 replies
RRCRat Rig Community [Unofficial]
•Created by omerk83 on 4/6/2025 in #fix-my-print
Purge blobs in the middle of a print
Any recommendations on a good PTFE tube? I guess AliExpress isn't good enough
23 replies
RRCRat Rig Community [Unofficial]
•Created by omerk83 on 4/6/2025 in #fix-my-print
Purge blobs in the middle of a print
Did this as well, thanks
23 replies
RRCRat Rig Community [Unofficial]
•Created by omerk83 on 4/6/2025 in #fix-my-print
Purge blobs in the middle of a print
I tried it but it didn't work, I think it might be the filament sensor itself, once I unplugged it completely the prints are working flawlessly with the same gcode.
23 replies
RRCRat Rig Community [Unofficial]
•Created by omerk83 on 4/6/2025 in #fix-my-print
Purge blobs in the middle of a print
Any idea where the clog macro is located? I also thought that I might move it to the filament change position so it doesn't ruin the print every time
23 replies
RRCRat Rig Community [Unofficial]
•Created by omerk83 on 4/6/2025 in #fix-my-print
Purge blobs in the middle of a print
Yeah that sounds about right, I tried to move the spool off the spool holder under the bed and I tested it now and there are still blobs, I even replaced the PTFE tube with a larger diameter one.
I thought that maybe I could just up the temps as well
23 replies
RRCRat Rig Community [Unofficial]
•Created by omerk83 on 4/6/2025 in #fix-my-print
Purge blobs in the middle of a print
I thought that might be the case but no, single color and no color swaps in the slicer
23 replies
RRCRat Rig Community [Unofficial]
•Created by omerk83 on 10/7/2024 in #fix-my-resonance
vc4 300 hybrid input shaper

4 replies
RRCRat Rig Community [Unofficial]
•Created by devart on 9/9/2024 in #fix-my-resonance
VC4 400 Hybrid
I don't know if that'll help but I had a problems with my belts as well.
What fixed it for me was to completely loosen the belts and move the gantry forward until it touches the front stoppers.
Then tighten up the belts just so it's touching the same on both rails.
Then do a first tune.
After every change to the belt tensioner home the printer before rerunning.
For me the movement helped to evenly distribute the load in the belts and I got a good graph
47 replies
RRCRat Rig Community [Unofficial]
•Created by omerk83 on 9/25/2024 in #ratos-support
RatOS wizard problems
@Oldschoolhippie, @c00ki3 vc4 300 hybrid Thank you both so much for the help I really appriciate it!
44 replies
RRCRat Rig Community [Unofficial]
•Created by omerk83 on 9/25/2024 in #ratos-support
RatOS wizard problems
It worked!
The steps: (like @Oldschoolhippie said)
Switch everything off
Remove the jumpers for the drivers
Plug the board into the Pi
Switch on the Pi
new attempt with RatOS wizard via manual DFU, not via autodetect
44 replies
RRCRat Rig Community [Unofficial]
•Created by omerk83 on 9/25/2024 in #ratos-support
RatOS wizard problems

44 replies
RRCRat Rig Community [Unofficial]
•Created by omerk83 on 9/25/2024 in #ratos-support
RatOS wizard problems

44 replies
RRCRat Rig Community [Unofficial]
•Created by omerk83 on 9/25/2024 in #ratos-support
RatOS wizard problems
@c00ki3 vc4 300 hybrid Thanks for all your help, I really appriciate the help!
44 replies
RRCRat Rig Community [Unofficial]
•Created by omerk83 on 9/25/2024 in #ratos-support
RatOS wizard problems
didnt work, changed the name and the power source. I might have to go get a 8 gb card
44 replies
RRCRat Rig Community [Unofficial]
•Created by omerk83 on 9/25/2024 in #ratos-support
RatOS wizard problems
I tried manual flashing after the DFU was not recognized by RatOS, should I try it again? do I need an sd card in for DFU?
44 replies
RRCRat Rig Community [Unofficial]
•Created by omerk83 on 9/25/2024 in #ratos-support
RatOS wizard problems
any idea how long it should take? or if the status LED should change?
44 replies
RRCRat Rig Community [Unofficial]
•Created by omerk83 on 9/25/2024 in #ratos-support
RatOS wizard problems
will do, im also formatting the new sd again to 4kb.
44 replies
RRCRat Rig Community [Unofficial]
•Created by omerk83 on 9/25/2024 in #ratos-support
RatOS wizard problems
i dont have electronics assembled yet but i have the rpi power supply that i can connect directly to the octopus
44 replies