James
RRCRat Rig Community [Unofficial]
•Created by Vini on 12/20/2024 in #ratos-support
Error evaluating 'gcode_macro INITIAL_FRONTEND_UPDATE:gcode
this happened to me, i had to start again, update ratos first then do them one at a time, worked for me
41 replies
RRCRat Rig Community [Unofficial]
•Created by Mikeeeeee on 11/6/2024 in #fix-my-printer
Hotend not heating on new vcore 400 Build
Hi Mike, james here think i was just talking to you on face book about tihs
4 replies
RRCRat Rig Community [Unofficial]
•Created by James on 10/13/2024 in #ratos-support
Rat Os crashes when trying to print large file (440mb)
that looks like its worked, thank you so much
23 replies
RRCRat Rig Community [Unofficial]
•Created by James on 10/13/2024 in #ratos-support
Rat Os crashes when trying to print large file (440mb)
ok i will try
23 replies
RRCRat Rig Community [Unofficial]
•Created by James on 8/18/2024 in #fix-my-print
anyone get any ideas
You can see the supports at the bottom of the model
11 replies
RRCRat Rig Community [Unofficial]
•Created by James on 8/18/2024 in #fix-my-print
anyone get any ideas
No the side of the print
11 replies
RRCRat Rig Community [Unofficial]
•Created by James on 8/18/2024 in #fix-my-print
anyone get any ideas
It's supposed to be smooth, so no lines at all, it's a rat rig vcore 3.1 500
11 replies
RRCRat Rig Community [Unofficial]
•Created by James on 8/18/2024 in #fix-my-print
anyone get any ideas
Hot end is pheatus rapido uhf 2. Orbitor extruder, filament is playing +
11 replies
RRCRat Rig Community [Unofficial]
•Created by James on 8/18/2024 in #fix-my-print
anyone get any ideas
Getting these lines when printing, everything is tight I've calibrated it and recalibrated
11 replies
RRCRat Rig Community [Unofficial]
•Created by James on 8/8/2024 in #fix-my-print
MCU 'toolboard_t0' shutdown: ADC out of range
New thermistor fixed it, thank you
24 replies
RRCRat Rig Community [Unofficial]
•Created by James on 8/8/2024 in #fix-my-print
MCU 'toolboard_t0' shutdown: ADC out of range
Just not getting any reading, I've ordered a replacement so fingers crossed it was was just a broken thermistor
24 replies
RRCRat Rig Community [Unofficial]
•Created by James on 8/8/2024 in #fix-my-print
MCU 'toolboard_t0' shutdown: ADC out of range
so i think the thermostate is dead not getting any resistance
24 replies
RRCRat Rig Community [Unofficial]
•Created by James on 8/8/2024 in #fix-my-print
MCU 'toolboard_t0' shutdown: ADC out of range
yeah i'll need to find it
24 replies
RRCRat Rig Community [Unofficial]
•Created by James on 8/8/2024 in #fix-my-print
MCU 'toolboard_t0' shutdown: ADC out of range
i do
24 replies
RRCRat Rig Community [Unofficial]
•Created by James on 8/8/2024 in #fix-my-print
MCU 'toolboard_t0' shutdown: ADC out of range
I D
24 replies
RRCRat Rig Community [Unofficial]
•Created by James on 8/8/2024 in #fix-my-print
MCU 'toolboard_t0' shutdown: ADC out of range
That good enough for you?
24 replies
RRCRat Rig Community [Unofficial]
•Created by James on 8/8/2024 in #fix-my-print
MCU 'toolboard_t0' shutdown: ADC out of range
24 replies
RRCRat Rig Community [Unofficial]
•Created by James on 8/8/2024 in #fix-my-print
MCU 'toolboard_t0' shutdown: ADC out of range
24 replies
RRCRat Rig Community [Unofficial]
•Created by James on 8/8/2024 in #fix-my-print
MCU 'toolboard_t0' shutdown: ADC out of range
24 replies
RRCRat Rig Community [Unofficial]
•Created by James on 8/8/2024 in #fix-my-print
MCU 'toolboard_t0' shutdown: ADC out of range
wiring is fine as there is an obvious difference when its connected and not connected. thermoster is cortrect and so is resistor and pin [extruder]
max_extrude_only_distance: 200
nozzle_diameter: 0.4
heater_pin: toolboard_t0:PB13
sensor_type: PT1000
pullup_resistor: 2200
sensor_pin: toolboard_t0:PA3
min_extrude_temp: 170
min_temp: 0
max_temp: 350
pressure_advance: 0.03
24 replies