EODesigns Comments - Answer Overflow

I started with the belt grabber flush to the rear printed part, and the m4 bolt flush with the threaded insert of the bent grabber. I then removed as much slack as I could by hand and trimmed. Tighten from there.

11 replies

RRCRat Rig Community [Unofficial]

•Created by WrinklySackNick on 12/23/2024 in #fix-my-resonance

Y accel wont go above 2000 - vcore 3.1 with toolhead

did you use new belts or trim your old ones? i found that my belts were just a little too long, and what i thought was tension through the belts was me running out of available adjustment on the belt grabber

11 replies

RRCRat Rig Community [Unofficial]

•Created by resmon on 12/26/2024 in #ratos-support

BTT eddy config with G28 called recursively, and calibration failed.

I think I commented that part out as well. I can confirm in a few days

19 replies

RRCRat Rig Community [Unofficial]

•Created by resmon on 12/26/2024 in #ratos-support

BTT eddy config with G28 called recursively, and calibration failed.

Did you ensure the Eddy was 2-3mm above the nozzle? I printed a spacer and made the mount adjustable to help ensure this.

19 replies

RRCRat Rig Community [Unofficial]

•Created by resmon on 12/26/2024 in #ratos-support

BTT eddy config with G28 called recursively, and calibration failed.

I've been able to successfully complete all the calibrations, but I'm definitely having some issues right now. They may be mechanical, so I'm reserving judgement on the probe at this time. I realized there was some looseness in one of my z motor mounts, so I'm gonna check that when I get back home before deciding to go with something else

19 replies

RRCRat Rig Community [Unofficial]

•Created by Qui1zy on 12/18/2024 in #ratos-support

BTT Eddy USB

Also, you have to install this exactly 2-3mm above the nozzle. Helpful to design a mount with some adjustability and print a 2.5mm spacer to sit the probe on when the nozzle is at 0

17 replies

RRCRat Rig Community [Unofficial]

•Created by Qui1zy on 12/18/2024 in #ratos-support

BTT Eddy USB

I've seen some inconsistencies with finding z0. This could be due to my z screws. I realized today the rear one was not completely tight to the frame. Gonna fix that over the weekend

17 replies

RRCRat Rig Community [Unofficial]

•Created by Qui1zy on 12/18/2024 in #ratos-support

BTT Eddy USB

If you're already in the install phase and using the device as a probe, you will need to comment out all of the [probe] statements

17 replies

RRCRat Rig Community [Unofficial]

•Created by Qui1zy on 12/18/2024 in #ratos-support

BTT Eddy USB

Are you trying to install, or making a purchase decision?

17 replies

RRCRat Rig Community [Unofficial]

•Created by Qui1zy on 12/18/2024 in #ratos-support

BTT Eddy USB

@Qui1zy I got it up and running on my VC3.1 400 a few weeks ago. I can share my cfg file when I get home in a few days. Not sure if I'm overall satisfied with the device though. I realized I didn't do the best job with the mechanical build, so I'm fixing a few things before passing final judgement

17 replies

RRCRat Rig Community [Unofficial]

•Created by resmon on 12/26/2024 in #ratos-support

BTT eddy config with G28 called recursively, and calibration failed.

Are you also using the Eddy to home z? If so, the way I got this to work was commenting out all of the [probe] statements

19 replies

RRCRat Rig Community [Unofficial]

•Created by dmeadows013 on 10/10/2023 in #fix-my-printer

Z Movement Clicking? Bad noise

Did you fix this? Having the same issue.

4 replies

RRCRat Rig Community [Unofficial]

•Created by EODesigns on 5/6/2024 in #fix-my-mesh

VC3.1 Enclosed 400 Back Corner Peak

Gonna try this!

16 replies

RRCRat Rig Community [Unofficial]

•Created by EODesigns on 5/6/2024 in #fix-my-mesh

VC3.1 Enclosed 400 Back Corner Peak

After some adjusting, my A, B, and D points are all within .102 of each other, but the overall range is .437. Not sure what I will gain by adjusting the front right down to bring up the back. The only thing I can think to do is adjust the back right (point C), but I know this is not advised

16 replies

RRCRat Rig Community [Unofficial]

•Created by EODesigns on 5/6/2024 in #fix-my-mesh

VC3.1 Enclosed 400 Back Corner Peak

16 replies

RRCRat Rig Community [Unofficial]

•Created by EODesigns on 5/6/2024 in #fix-my-mesh

VC3.1 Enclosed 400 Back Corner Peak

I should add this is all at room temp, as the commissioning guide seems to want me to wait to install the heater until this is done.

16 replies

Gaming

Programming