psyvision
RRCRat Rig Community [Unofficial]
•Created by psyvision on 2/23/2024 in #fix-my-print
First Layer / Mesh Problem
Yea that wouldn't help 😄
17 replies
RRCRat Rig Community [Unofficial]
•Created by psyvision on 2/23/2024 in #fix-my-print
First Layer / Mesh Problem
You can also see the z couplers spinning and the Z changing in the UI as the head moves
17 replies
RRCRat Rig Community [Unofficial]
•Created by psyvision on 2/23/2024 in #fix-my-print
First Layer / Mesh Problem
It doesn't have a saved mesh but meshes before each print, mainsail shows it as loaded in the tool window too.
17 replies
RRCRat Rig Community [Unofficial]
•Created by psyvision on 2/23/2024 in #fix-my-print
First Layer / Mesh Problem
I am also using a textured PEI sheet and have no 2020 extrusion in my X axis - enclosed machine
17 replies
RRCRat Rig Community [Unofficial]
•Created by psyvision on 2/23/2024 in #fix-my-print
First Layer / Mesh Problem
I've widened my total mesh area which was previously reduced (mesh min and max)
17 replies
RRCRat Rig Community [Unofficial]
•Created by psyvision on 2/23/2024 in #fix-my-print
First Layer / Mesh Problem
I'm using BED_MESH_OFFSET but I think not quite right still
17 replies
RRCRat Rig Community [Unofficial]
•Created by psyvision on 2/23/2024 in #fix-my-print
First Layer / Mesh Problem
I've tuned my extrusion multiplier (reduced) using Ellis method
17 replies
RRCRat Rig Community [Unofficial]
•Created by psyvision on 2/23/2024 in #fix-my-print
First Layer / Mesh Problem
I'm using klippers built in adaptive bed mesh
17 replies
RRCRat Rig Community [Unofficial]
•Created by psyvision on 2/23/2024 in #fix-my-print
First Layer / Mesh Problem
I've stopped using a really old version of PAM (uninstalled)
17 replies
RRCRat Rig Community [Unofficial]
•Created by psyvision on 2/23/2024 in #fix-my-print
First Layer / Mesh Problem
I've improved it a lot. My machine is very non standard but here's what I've done
17 replies
RRCRat Rig Community [Unofficial]
•Created by McNik on 12/26/2023 in #ratos-support
Beacon Y-Offset out of bounds
Mesh_min in bedmesh changes the mesh lower limit. Can't view your config atm, mobile
16 replies
RRCRat Rig Community [Unofficial]
•Created by other-emerald on 2/24/2023 in #fix-my-printer
V Core 3 CAN communication configuration
correct
10 replies
RRCRat Rig Community [Unofficial]
•Created by foreign-sapphire on 2/8/2023 in #ratos-support
Pause Print: Move Out of Range (Tool-Changer)
https://github.com/TypQxQ/Klipper_ToolChanger - It's also written by someone who has a Jubilee and runs Klipper
51 replies
RRCRat Rig Community [Unofficial]
•Created by unwilling-turquoise on 2/8/2023 in #ratos-support
Pause Print: Move Out of Range (Tool-Changer)
Yea I don't mess around with macros. I use the Klipper_ToolChanger plugin, much easier. For PAUSE I simply just overwrite the RatOS macro with one that just lifts the nozzle 10mm, but it would be trivial to implement offset adjusted parking if needed due to the extra info the plugin gives.
51 replies
RRCRat Rig Community [Unofficial]
•Created by psyvision on 12/5/2022 in #ratos-support
Raspberry Pi Dropping Wifi
Switched to 5GHz and will see how that holds up
10 replies
RRCRat Rig Community [Unofficial]
•Created by psyvision on 12/5/2022 in #ratos-support
Raspberry Pi Dropping Wifi
I did find a super long spare network cable in the loft and that might be the answer 😄
10 replies
RRCRat Rig Community [Unofficial]
•Created by psyvision on 12/5/2022 in #ratos-support
Raspberry Pi Dropping Wifi
I might look at that (I think I had seen it before in their github). I don't run an update RatOS 😉 so no conflicts will occur here. My network is pretty good stuff (UniFi) and this seems to be the only thing that does it. I usually turn it off each night but didn't last night and voila...
10 replies
RRCRat Rig Community [Unofficial]
•Created by conscious-sapphire on 12/4/2022 in #fix-my-print
wavy corners
Have you actually lubricated them?
60 replies