DocDoyle
RRCRat Rig Community [Unofficial]
•Created by MFBS on 8/27/2024 in #fix-my-resonance
No matter what I do I can not get rid of the third hump
can you hear what is vibrating on that second peak?
75 replies
RRCRat Rig Community [Unofficial]
•Created by MFBS on 8/27/2024 in #fix-my-resonance
No matter what I do I can not get rid of the third hump
with the ADXL being very close to the carriage, its Z movement was measured to be very low (at a small distance from the carriage), but the nozzle tip was moving significantly, even causing ringing in the Z axis
75 replies
RRCRat Rig Community [Unofficial]
•Created by MFBS on 8/27/2024 in #fix-my-resonance
No matter what I do I can not get rid of the third hump
do your X/Y graphs contain the third bump? ive seen three bumps on belt/Y graph with a wobbly X rail, where it would not resonate in X/Y but in a rotational component of the X axis, with a small peak of Z movement
75 replies
RRCRat Rig Community [Unofficial]
•Created by Jasmin on 7/16/2024 in #fix-my-mesh
Wave in bed (VC4-500)
ive printed plenty of things with 0.5/0.6 diviation
18 replies
RRCRat Rig Community [Unofficial]
•Created by Jasmin on 7/16/2024 in #fix-my-mesh
Wave in bed (VC4-500)
0.327 is not the complete end of the world as well
18 replies
RRCRat Rig Community [Unofficial]
•Created by Jasmin on 7/16/2024 in #fix-my-mesh
Wave in bed (VC4-500)
perhaps it can give away the issue
18 replies
RRCRat Rig Community [Unofficial]
•Created by Jasmin on 7/16/2024 in #fix-my-mesh
Wave in bed (VC4-500)
and on the gantry
18 replies
RRCRat Rig Community [Unofficial]
•Created by Jasmin on 7/16/2024 in #fix-my-mesh
Wave in bed (VC4-500)
can always try a long straight edge on the bed
18 replies
RRCRat Rig Community [Unofficial]
•Created by solmaelstrom on 7/11/2024 in #fix-my-resonance
shaper graph low y acceleration V Core 500
Its roughly the same to how my VC500 3.0 was before upgrades, but id imagine the metal layout on a VC4 can take some more tension, you could defenitly try a bit more belt tension
16 replies
RRCRat Rig Community [Unofficial]
•Created by solmaelstrom on 7/11/2024 in #fix-my-resonance
shaper graph low y acceleration V Core 500
Since it can very greatly with similar belt tensions
16 replies
RRCRat Rig Community [Unofficial]
•Created by solmaelstrom on 7/11/2024 in #fix-my-resonance
shaper graph low y acceleration V Core 500
That is not how that value of 4e6 works
16 replies
RRCRat Rig Community [Unofficial]
•Created by LynX83 on 7/7/2024 in #fix-my-printer
new vcore-3.1 500 do not extrude whit LGX and rapido phateus v2
That is an interesting swirl you got there
8 replies
RRCRat Rig Community [Unofficial]
•Created by LynX83 on 7/7/2024 in #fix-my-printer
new vcore-3.1 500 do not extrude whit LGX and rapido phateus v2
Is the toolhead cooling fan spinning? Is it spinning in the correct way?
8 replies
RRCRat Rig Community [Unofficial]
•Created by LynX83 on 7/7/2024 in #fix-my-printer
new vcore-3.1 500 do not extrude whit LGX and rapido phateus v2
Can you push filament throug by hand?
8 replies
RRCRat Rig Community [Unofficial]
•Created by Diego on 7/13/2024 in #fix-my-printer
Can I fix my octopus v1.1?
probably a big nope, unless you have advanced knowledge of repairing PCB's and tracking/replacing burnt components
4 replies
RRCRat Rig Community [Unofficial]
•Created by solmaelstrom on 7/10/2024 in #fix-my-mesh
hump In bed (V Core 4 500mm)
causing bumps in my bed mesh
21 replies
RRCRat Rig Community [Unofficial]
•Created by solmaelstrom on 7/10/2024 in #fix-my-mesh
hump In bed (V Core 4 500mm)
some of the stuff that sits on top of the flex steel plate was scattered on the bottom as well
21 replies
RRCRat Rig Community [Unofficial]
•Created by solmaelstrom on 7/10/2024 in #fix-my-mesh
hump In bed (V Core 4 500mm)
i had this and there was a line of some of the textured grain on the bottom. perhaps something else underneath?
21 replies
RRCRat Rig Community [Unofficial]
•Created by vhaude on 5/8/2024 in #fix-my-resonance
Lower max Accel after installing FMMM, ToroTube and Motor Decouplers
I follow this document and use the "Measure corexy belt tension" macro which plots the frequency graphs of both belts
5 replies
RRCRat Rig Community [Unofficial]
•Created by vhaude on 5/8/2024 in #fix-my-resonance
Lower max Accel after installing FMMM, ToroTube and Motor Decouplers
seems like there is perhaps a difference in belt tension, id verify if those are correct or similar as before
5 replies