Torque
RRCRat Rig Community [Unofficial]
•Created by Torque on 11/17/2024 in #fix-my-mesh
Adaptive mesh compensation- how to turn off?
By the second layer of this current print I've swung from 0.13 all the way to 0.31 by the 2nd layer. On the 2nd layer it comes out looking smooth at least to the eye. Could be an illusion though.
5 replies
RRCRat Rig Community [Unofficial]
•Created by Torque on 11/17/2024 in #fix-my-mesh
Adaptive mesh compensation- how to turn off?
As you can see in the photos the mesh starts out meh at the right, i then adjust and get it good- (disc on the right) then when it starts the disc to the left it gets all screwed up again likes there is no compensation happening there.
5 replies
RRCRat Rig Community [Unofficial]
•Created by Torque on 11/17/2024 in #fix-my-mesh
Adaptive mesh compensation- how to turn off?
5 replies
RRCRat Rig Community [Unofficial]
•Created by Torque on 11/14/2024 in #fix-my-printer
Weird squeaking in toolhead
It's causing some kind of extrusion issue as it's starts stringing and bobbing after running for an hour perfectly fine.
7 replies
RRCRat Rig Community [Unofficial]
•Created by Torque on 11/14/2024 in #fix-my-printer
Weird squeaking in toolhead
Ruins the print
7 replies
RRCRat Rig Community [Unofficial]
•Created by Torque on 11/14/2024 in #fix-my-printer
Weird squeaking in toolhead
Squealing not popping. Right in the beginning of the video.
7 replies
RRCRat Rig Community [Unofficial]
•Created by Torque on 11/14/2024 in #fix-my-printer
Weird squeaking in toolhead
7 replies
RRCRat Rig Community [Unofficial]
•Created by SithMaster015 on 11/5/2024 in #fix-my-print
PETG Problems
Also dry your filament
10 replies
RRCRat Rig Community [Unofficial]
•Created by SithMaster015 on 11/5/2024 in #fix-my-print
PETG Problems
Download orcaslicer and never look back. Once you get familiar with it come back and I ill share my settings. I have perfect petg bridging settings.
10 replies
RRCRat Rig Community [Unofficial]
•Created by Kosmák on 11/1/2024 in #fix-my-print
Weird ripple effect on otherwise flawless PETG-CF print
7 replies
RRCRat Rig Community [Unofficial]
•Created by Kosmák on 11/1/2024 in #fix-my-print
Weird ripple effect on otherwise flawless PETG-CF print
7 replies
RRCRat Rig Community [Unofficial]
•Created by Steppe_Warrior on 8/20/2024 in #fix-my-print
And here we go again... first layer problem even with beacon3D
Has anyone confirmed my suspisions a few weeks back that its a klipper problem? I have had the same issue on 2 different printers. The only common thread is they both run klipper and they both started doing it after a klipper update.
80 replies
RRCRat Rig Community [Unofficial]
•Created by ShadowViper on 10/22/2024 in #fix-my-printer
Nozzle gets closer to the bed every time during first layer (worse at higher temps).
I believe many of us are having the same issue. I always have to increase z height by about 0.07 for it to start flattening out. The trouble is even though I don't save the z height it ends up re-meshing every print so I have to adjust again and again. There is a post here somewhere where Mikkel says to add an temp offset in the printer.cfg or something to save changes for different filaments.
5 replies
RRCRat Rig Community [Unofficial]
•Created by JphiLamalice on 10/10/2024 in #fix-my-print
PETG bridging issue
Make sure to mark the problem as solved
12 replies
RRCRat Rig Community [Unofficial]
•Created by JphiLamalice on 10/10/2024 in #fix-my-print
PETG bridging issue
Awesome. Glad I could help. Yeah that's a new feature that I found was critical to getting the bridge to adhere at rhe beginning of its travel. It slows down the toolhead smoothly like a ramp instead of a cliff just before it leaves the part to form the bridge.
12 replies
RRCRat Rig Community [Unofficial]
•Created by tg73 on 10/8/2024 in #fix-my-print
Regular surface distortion pattern towards end of larger first layers VC4
Sigh...Still struggling with first layers on my $2500 machine. Take the same friggin brand new filament and swap it over to my $600 BL and With zero calibration whatsoever it prints an absolutely perfect 1st layer. And the bed is even bowed slightly. Whyyyyyyyyy
1729 replies
RRCRat Rig Community [Unofficial]
•Created by JphiLamalice on 10/10/2024 in #fix-my-print
PETG bridging issue
Set fan speeds in your filament profile to minimum of 30 when bridging but more likely 60
12 replies
RRCRat Rig Community [Unofficial]
•Created by JphiLamalice on 10/10/2024 in #fix-my-print
PETG bridging issue
turn classic mode off and turn on extrusion rate smoothing to 350
12 replies
RRCRat Rig Community [Unofficial]
•Created by JphiLamalice on 10/10/2024 in #fix-my-print
PETG bridging issue
There is your problem right there. Your Overhang speeds should be from top to bottom like this= 75,50,30,20,15,20
12 replies
RRCRat Rig Community [Unofficial]
•Created by Chrizzar on 1/19/2023 in #fix-my-mesh
Corner dip. Bed level with PAM. Uneven first layer. i.e. perfect layer one side, opposite too close
A clean z offset calibration with the nozzle wiped clean with a wire brush did the trick it seems.
20 replies