MARC
RRCRat Rig Community [Unofficial]
•Created by MARC on 2/12/2024 in #fix-my-print
Eclipson airplanes helix printing issues.
"-MISSING INTERNAL STRUCTURE WITH PRUSALICER / BAMBU STUDIO
Reason: The parameter "slice gap closing radius" is 0,049 mm by default. In some of our models we use smaller gaps so the software will erese this material.
Solution: Reduce the value up to 0"
3 replies
RRCRat Rig Community [Unofficial]
•Created by MARC on 2/12/2024 in #fix-my-print
Eclipson airplanes helix printing issues.
3 replies
RRCRat Rig Community [Unofficial]
•Created by MARC on 1/12/2024 in #fix-my-print
OVERTURE LW-PLA issues after seam.
Just an update. Purchased another roll. Seems to print a lot better. Max speed is 60mm/s with a 0.4mm nozzle. 210c, retraction setting 1.5 minimum. If you get stringing, increase retraction but slow down your acceleration. I usually run 12k acceleration outer walls but that's down to 3k just for this filament. The filament is not the best to work with. If you set klipper to extrude 50mm at 10mm/s, you will see a half second delay before anything comes out. No other filament does that with me.
7 replies
RRCRat Rig Community [Unofficial]
•Created by MARC on 1/12/2024 in #fix-my-print
OVERTURE LW-PLA issues after seam.
7 replies
RRCRat Rig Community [Unofficial]
•Created by MARC on 1/12/2024 in #fix-my-print
OVERTURE LW-PLA issues after seam.
7 replies
RRCRat Rig Community [Unofficial]
•Created by MARC on 1/12/2024 in #fix-my-print
OVERTURE LW-PLA issues after seam.
I have tried superslicer, prusa slicer, orca and cura. All have exactly the same issue. Removing wipe on retracts helps ALOT however, I thought I had it figured but I still go the issue right at the end of my print...
7 replies
RRCRat Rig Community [Unofficial]
•Created by MARC on 11/24/2023 in #fix-my-printer
Z1 stepper overtemp error.
that is my printer cfg
12 replies
RRCRat Rig Community [Unofficial]
•Created by MARC on 11/24/2023 in #fix-my-printer
Z1 stepper overtemp error.
It will be a while before I have access to my garage but I can connect to it and send my printer cfg, 2 sec
12 replies
RRCRat Rig Community [Unofficial]
•Created by MARC on 11/24/2023 in #fix-my-printer
Z1 stepper overtemp error.
After more testing and inspecting, I noticed that z1 motor was at a slight angle. Not sitting truly straight. I'm wondering if the vibration from input shaping was allowing the motor to somehow drop and touch the metal bracket under it? If the motor picked up vibration from direct contact to the frame, would it cause errors? I forgot to mention that I installed the Eva toolhead upgrade. So I had to rebelt and align my x axis so my vibrations could be different. Maybe I did something wrong there?
12 replies
RRCRat Rig Community [Unofficial]
•Created by MARC on 11/24/2023 in #fix-my-printer
Z1 stepper overtemp error.
So after more testing, it seems to be when I use input sharing in my ebb42 1.2. I can get the error to pop up 100% when I use input shaping. I made up a quick macro to home, z tilt 30 times and I never got the error. I started shaper_calibrate and after it does the first test, I get the z1 overheat error
12 replies
RRCRat Rig Community [Unofficial]
•Created by MARC on 11/24/2023 in #fix-my-printer
Z1 stepper overtemp error.
I can get that error just leaving the printer idle. If I switch z1 to z2 for example, I will still get the overheat z1 error. So it's not motor dependant. Doesn't matter if I replace a stepper driver or put a new one in. It still comes up with the z1 overheat. I might have to override that stepper plug and use another one.
12 replies
RRCRat Rig Community [Unofficial]
•Created by MARC on 11/24/2023 in #fix-my-printer
Z1 stepper overtemp error.
Yes. I have 2. 1 blowing on my xy and another one blowing on my z motors.
12 replies
RRCRat Rig Community [Unofficial]
•Created by MARC on 7/8/2023 in #ratos-support
Manta m8p cb1 no wifi, ethernet or usb wifi connection.
Thanks for the help. I have a spare raspberry pi set up with an os. I'll end up using that when I get the time!
27 replies
RRCRat Rig Community [Unofficial]
•Created by MARC on 7/8/2023 in #ratos-support
Manta m8p cb1 no wifi, ethernet or usb wifi connection.
When I plug the sd card in, I can see 2 partitions. Boot and another one I can't access. The boot one has a gcode folder but it's empty. It's exactly the same as the fresh sd card. I can't seem to find any cfg files or anything.
27 replies
RRCRat Rig Community [Unofficial]
•Created by MARC on 7/8/2023 in #ratos-support
Manta m8p cb1 no wifi, ethernet or usb wifi connection.
Just an update. It must be a dodgy sd card slot. If I push the sd card in and put pressure on it, everything seems to work fine. If I push it in normally it doesn't seem to work. Well it does but, I get the wifi issues. This fix only seems to work with the fresh sd card with ratos. @miklschmidt was right. I must have ruined the file system either by user error or when I removed the sd card in the past, I might have been lucky with it working. For now I have a cable tie around the board. Thanks for all your help!
I also have another question. I can still see files on the original sd card. Is it possible to get the original cfg files and gcode files from it? I have some stuff there I really don't want to lose.
27 replies
RRCRat Rig Community [Unofficial]
•Created by MARC on 7/8/2023 in #ratos-support
Manta m8p cb1 no wifi, ethernet or usb wifi connection.
I just get "this site can't be reached" "took to long to respond"
27 replies
RRCRat Rig Community [Unofficial]
•Created by MARC on 7/8/2023 in #ratos-support
Manta m8p cb1 no wifi, ethernet or usb wifi connection.
Right so, if I power on the printer with the fresh sd card and rat os. If I leave it alone I can see the wifi on all my devices. As soon as I connect to it, I've got a few seconds before it turns off.
27 replies
RRCRat Rig Community [Unofficial]
•Created by MARC on 7/8/2023 in #ratos-support
Manta m8p cb1 no wifi, ethernet or usb wifi connection.
When I plug the ethernet straight to my laptop, I can get the ip address from the cmd prompt. However, if I use the ratos.local/configure link or the ip link, I just get the same error. This is happening with both of my cb1 boards. Both are v2.2. I really hope it isn't the mcu board itself.
27 replies
RRCRat Rig Community [Unofficial]
•Created by MARC on 7/8/2023 in #ratos-support
Manta m8p cb1 no wifi, ethernet or usb wifi connection.
My phone can connect to the ratos fast enough to allow me to see the config page but again, I lose the connection.
27 replies
RRCRat Rig Community [Unofficial]
•Created by MARC on 7/8/2023 in #ratos-support
Manta m8p cb1 no wifi, ethernet or usb wifi connection.
Ethernet has never worked for me. That was the first thing I tried when I struggled with wifi.
27 replies