skyline131313
skyline131313
PostsComments
RRCRat Rig Community [Unofficial]
Created by skyline131313 on 3/29/2024 in #fix-my-printer
Z wobble or some sort of problem with gantry?
No description
6 replies
RRCRat Rig Community [Unofficial]
Created by skyline131313 on 3/20/2024 in #fix-my-print
Corners Warping with ABS
Can't seem to get rid of warping completely with ABS. I have chamber at 45 C and have tried 50 C but the corners still warp. Brim doesn't help and I've tried doing a custom brim but still lifts. I've tried glue stick before but I'd rather not use it as it is messy and I have a bl touch probe. I have bed temp set to 110 and nozzle 255 C to start and then 250 C for the rest. Using textured PEI buildplate. Idk if there is anything else I can try without using something like a glue stick? If I have to use an extra adhesive, is there something better than a glue stick? I've heard hairspray is also good? I know there are some name brand adhesives but they tend to all be pretty expensive along with added shipping costs.
25 replies
RRCRat Rig Community [Unofficial]
Created by skyline131313 on 3/6/2024 in #fix-my-printer
Hotend Heater going too high?
No description
4 replies
RRCRat Rig Community [Unofficial]
Created by skyline131313 on 2/23/2024 in #fix-my-printer
Bad First Layer Outside of Probed Area
No description
11 replies
RRCRat Rig Community [Unofficial]
Created by skyline131313 on 2/20/2024 in #ratos-support
ratos-configurator showing as invalid
No description
25 replies
RRCRat Rig Community [Unofficial]
Created by skyline131313 on 1/27/2024 in #fix-my-print
Blobs on edges of top layer infill
No description
8 replies
RRCRat Rig Community [Unofficial]
Created by skyline131313 on 12/28/2023 in #fix-my-printer
Getting More Consistent First Layer and Z Tilt Issue Related?
No description
5 replies
RRCRat Rig Community [Unofficial]
Created by skyline131313 on 9/21/2023 in #fix-my-print
First Layer has Lots of Gaps?
No description
41 replies
RRCRat Rig Community [Unofficial]
Created by skyline131313 on 9/19/2023 in #fix-my-printer
Loud Z Lead Screw when moving bed down
I was working on the printer and did some changes on the gantry to add ABS printed parts. I didn't touch the bed or make adjustments to the frame. The left Z lead screw became really noisy for some reason. When it moves down at a Section in the beginning it is really loud. There's no binding, I can easily rotate the motor by hand where it still makes the sound just not as loud.
4 replies
RRCRat Rig Community [Unofficial]
Created by skyline131313 on 9/13/2023 in #fix-my-print
Issue with overhang first layer and support bridging
No description
25 replies
RRCRat Rig Community [Unofficial]
Created by skyline131313 on 9/10/2023 in #fix-my-printer
MCU Shutdown Error occasionally when heightmap probing
Only happens when doing the heightmap when starting a print, and only sometimes. I've tried a backup pi4 I have, tried a different sd card, have a separate PSU connected to it for 5v. Still have the same problem. Using it with a spider v2.3 controller board. Added the log I have for the last time it happened. I don't restart the rpi I just do the firmware restart on the controller board and then it goes fine. I've done 10+ hour prints without getting this error, just when it does the heightmapping and only sometimes. 
Transition to shutdown state: MCU 'mcu' shutdown: Timer too close
This often indicates the host computer is overloaded. Check
for other processes consuming excessive CPU time, high swap
usage, disk errors, overheating, unstable voltage, or
similar system problems on the host computer.
Transition to shutdown state: MCU 'mcu' shutdown: Timer too close
This often indicates the host computer is overloaded. Check
for other processes consuming excessive CPU time, high swap
usage, disk errors, overheating, unstable voltage, or
similar system problems on the host computer.
30 replies