dfos
RRCRat Rig Community [Unofficial]
•Created by Hydr0s on 11/25/2024 in #fix-my-printer
Tool head errors when going Hybrid to IDEX
No need to reflash the SD card, just start the configuration wizard with a fresh printer.cfg
8 replies
RRCRat Rig Community [Unofficial]
•Created by Hydr0s on 11/25/2024 in #fix-my-printer
Tool head errors when going Hybrid to IDEX
Start fresh, don't reuse the old printer.cfg. That solved it for me
8 replies
RRCRat Rig Community [Unofficial]
•Created by el mariano on 11/25/2024 in #fix-my-printer
Visual calibration tab didn't show image from VAOC camera
If so, try to change the device path to /dev/RatOS/rr-vaoc-camera
10 replies
RRCRat Rig Community [Unofficial]
•Created by el mariano on 11/25/2024 in #fix-my-printer
Visual calibration tab didn't show image from VAOC camera
Or are you saying that you have actually no image?
10 replies
RRCRat Rig Community [Unofficial]
•Created by el mariano on 11/25/2024 in #fix-my-printer
Visual calibration tab didn't show image from VAOC camera
Is the nozzle right on the camera?
10 replies
RRCRat Rig Community [Unofficial]
•Created by archen on 11/25/2024 in #fix-my-printer
IDEX inconcistent nozzle alignment
My nozzles never align on VAOC
110 replies
RRCRat Rig Community [Unofficial]
•Created by archen on 11/25/2024 in #fix-my-printer
IDEX inconcistent nozzle alignment
I'm also having issues
110 replies
RRCRat Rig Community [Unofficial]
•Created by archen on 11/25/2024 in #fix-my-printer
IDEX inconcistent nozzle alignment
Did you increase belt tension?
110 replies
RRCRat Rig Community [Unofficial]
•Created by archen on 11/25/2024 in #fix-my-printer
IDEX inconcistent nozzle alignment
Do your nozzles align in the VAOC camera? For example, align T0 and then T1. If you go back to T0, is T0 aligned?
110 replies
RRCRat Rig Community [Unofficial]
•Created by 3D Scharti on 11/23/2024 in #fix-my-printer
SSR not switching bed power
Do you have a multimeter/voltmeter?
16 replies
RRCRat Rig Community [Unofficial]
•Created by devart on 9/9/2024 in #fix-my-resonance
VC4 400 Hybrid
Oh, but yours is 400,so the frequency should be lower, I guess
47 replies
RRCRat Rig Community [Unofficial]
•Created by devart on 9/9/2024 in #fix-my-resonance
VC4 400 Hybrid
47 replies
RRCRat Rig Community [Unofficial]
•Created by devart on 9/9/2024 in #fix-my-resonance
VC4 400 Hybrid
For just the coreXY belts
47 replies
RRCRat Rig Community [Unofficial]
•Created by devart on 9/9/2024 in #fix-my-resonance
VC4 400 Hybrid
Are the belts tight? The frequency seems low. My peak is at 76Hz
47 replies
RRCRat Rig Community [Unofficial]
•Created by devart on 9/9/2024 in #fix-my-resonance
VC4 400 Hybrid
@devart Have you fixed the issue?
47 replies
RRCRat Rig Community [Unofficial]
•Created by 03Julian04 on 9/18/2024 in #fix-my-printer
Need help please: „Error during homing contact: Contact triggered while accelerating“ /RatRig V4 500
Oh, I didn't even see this when I was configuring. I ended up manually increasing the current in printer.cfg
Now I know, thanks!
12 replies
RRCRat Rig Community [Unofficial]
•Created by Belly on 9/11/2024 in #fix-my-print
is this a cooling issue?
Let's mark this as "Solved"
30 replies
RRCRat Rig Community [Unofficial]
•Created by Belly on 9/11/2024 in #fix-my-print
is this a cooling issue?
Well, we are both idiots then ahahah
30 replies
RRCRat Rig Community [Unofficial]
•Created by 03Julian04 on 9/18/2024 in #fix-my-printer
Need help please: „Error during homing contact: Contact triggered while accelerating“ /RatRig V4 500
Can you elaborate on what performance mode is?
12 replies
RRCRat Rig Community [Unofficial]
•Created by jb02877 on 9/20/2024 in #fix-my-printer
Temperature Wait issue
The target is 150 because it's the temperature Beacon contact is calibrated at. I don't recommend disabling this. You are just 'wasting' 30s for the benefit of a good first layer
6 replies