Decker
Decker
PostsComments
RRCRat Rig Community [Unofficial]
Created by Decker on 1/7/2025 in #ratos-support
pin PD12 used multiple times in config
Trying to set up two fans for the drivers, adding the following lines results in an error pin PD12 used multiple times in config: On lines 137-145 of printer.cfg, 
[controller_fan controller_fan_1]
pin:PD12

[controller_fan controller_fan_2]
pin:PD13
[controller_fan controller_fan_1]
pin:PD12

[controller_fan controller_fan_2]
pin:PD13
I don't know where PD12 is used previously. Also, could I simplify this to [controller_fan controller_fan_1] pin:PD12, PD13 and should I tie the enable_pin to the steppers?
21 replies
RRCRat Rig Community [Unofficial]
Created by Decker on 1/3/2025 in #fix-my-resonance
Weird Tail
No description
13 replies
RRCRat Rig Community [Unofficial]
Created by Decker on 1/2/2025 in #ratos-support
Changed stepper_x setting, now ratos error
I made a change in my printer.cfg to adjust my position_endstop and now I'm getting an ERROR about allow_unknown_gcode_generator, a value i never touched Ran a few updates this morning and didnt run into this issue until now 
Option 'allow_unknown_gcode_generator' is not valid in section 'ratos'

Once the underlying issue is corrected, use the "RESTART"
command to reload the config and restart the host software.
Printer is halted
Option 'allow_unknown_gcode_generator' is not valid in section 'ratos'

Once the underlying issue is corrected, use the "RESTART"
command to reload the config and restart the host software.
Printer is halted
20 replies
RRCRat Rig Community [Unofficial]
Created by Decker on 8/18/2024 in #fix-my-printer
Consistent Jams With Chube
No description
78 replies
RRCRat Rig Community [Unofficial]
Created by Decker on 7/14/2024 in #ratos-support
Error during homing contact on repeated prints
No description
115 replies
RRCRat Rig Community [Unofficial]
Created by Decker on 10/15/2023 in #fix-my-printer
Big Layer Shifts
No description
54 replies
RRCRat Rig Community [Unofficial]
Created by Decker on 7/30/2023 in #fix-my-resonance
Post Enclosure Kit Resonance
No description
7 replies
RRCRat Rig Community [Unofficial]
Created by Decker on 7/1/2023 in #fix-my-printer
Rapido 2 ADC out of range
Installed a Rapido 2 Plus and get a klipper shutdown nearly instantly. printer.cfg contains an override of sensor_type: PT1000 The enabled hotend config is [include config/hotends/rapido.cfg] Previous hotend was a Rapido 1 (not Plus), (that had a damaged wire, thus the upgrade) e: It has been mentioned that it's possibly a bad crimp job. Don't know how to test that Klipper message: 
MCU 'mcu' shutdown: ADC out of range
This generally occurs when a heater temperature exceeds
its configured min_temp or max_temp.
Once the underlying issue is corrected, use the
"FIRMWARE_RESTART" command to reset the firmware, reload the
config, and restart the host software.
Printer is shutdown
MCU 'mcu' shutdown: ADC out of range
This generally occurs when a heater temperature exceeds
its configured min_temp or max_temp.
Once the underlying issue is corrected, use the
"FIRMWARE_RESTART" command to reset the firmware, reload the
config, and restart the host software.
Printer is shutdown
26 replies
RRCRat Rig Community [Unofficial]
Created by Decker on 6/28/2023 in #fix-my-printer
Rapido Thermistor Repair?
No description
12 replies
RRCRat Rig Community [Unofficial]
Created by Decker on 5/17/2023 in #fix-my-printer
Sparks and No Heat
No description
3 replies
RRCRat Rig Community [Unofficial]
Created by Decker on 2/9/2023 in #fix-my-printer
Deep Resonance
No description
103 replies