Woodside
RRCRat Rig Community [Unofficial]
•Created by Woodside on 9/10/2024 in #fix-my-print
Variations in Layer Lines Around Geometry Changes
Not perfect but 90% better. Wild. That's not an artifact I would've anticipated being caused by that.
6 replies
RRCRat Rig Community [Unofficial]
•Created by Woodside on 9/10/2024 in #fix-my-print
Variations in Layer Lines Around Geometry Changes
Just as a sanity check I printed a cylinder which does not contain the same band. I.e. rules out z-wobble.
6 replies
RRCRat Rig Community [Unofficial]
•Created by Woodside on 8/21/2024 in #fix-my-print
Zig-zag rippling on print
Unfortunate result but yeah, bad nozzle
11 replies
RRCRat Rig Community [Unofficial]
•Created by Woodside on 8/21/2024 in #fix-my-print
Zig-zag rippling on print
It appears to have been a bad nozzle
11 replies
RRCRat Rig Community [Unofficial]
•Created by Woodside on 8/21/2024 in #fix-my-print
Zig-zag rippling on print
In the ballpark at least. I've never seen under/over extrusion cause this though.
I'm starting to suspect a bad nozzle, but that'd take buying a new nozzle to test. May just go ahead and order one.
11 replies
RRCRat Rig Community [Unofficial]
•Created by Woodside on 8/21/2024 in #fix-my-print
Zig-zag rippling on print
11 replies
RRCRat Rig Community [Unofficial]
•Created by Woodside on 8/21/2024 in #fix-my-print
Zig-zag rippling on print
Tightened the screws on the extruder. Seeing if that helps...
11 replies
RRCRat Rig Community [Unofficial]
•Created by Woodside on 8/21/2024 in #fix-my-print
Zig-zag rippling on print
Kinda hard to see on the hull of the benchy no matter what I do but hopefully it's visible enough
11 replies
RRCRat Rig Community [Unofficial]
•Created by Woodside on 11/26/2023 in #fix-my-print
Voids in layer after detail change
(Just saw this reply)
I'll try that. I did tune PA so I knew that wasn't it.
5 replies
RRCRat Rig Community [Unofficial]
•Created by Woodside on 11/26/2023 in #fix-my-print
Voids in layer after detail change
There are similar artifacts on the interior of the boat, always the first couple of layers after a new feature starts.
5 replies
RRCRat Rig Community [Unofficial]
•Created by Woodside on 11/22/2023 in #fix-my-printer
[Solved] Cooling Fan Speed Inverted
Ah I see, it's mentioned here albeit indirectly
https://os.ratrig.com/docs/guides/4028/#pwm
2 replies
RRCRat Rig Community [Unofficial]
•Created by Woodside on 5/7/2023 in #fix-my-printer
X gantry has a "sine"-like resistance variance when moving along Y
So it's normal & goes away with some "warm up"?
15 replies
RRCRat Rig Community [Unofficial]
•Created by Woodside on 5/7/2023 in #fix-my-printer
X gantry has a "sine"-like resistance variance when moving along Y
For what? Being aligned vertically with the bearings? They seem to be.
Though as of now the variance in resistance is low. But still kinda wavy in variance.
15 replies
RRCRat Rig Community [Unofficial]
•Created by Woodside on 5/7/2023 in #fix-my-printer
X gantry has a "sine"-like resistance variance when moving along Y
I've tried installing the pulley with multiple tactics (including pushing against the apogee of the runout when installing) but nothing's fixing it. I'm ordering replacement pulleys and hoping that does the trick.
15 replies
RRCRat Rig Community [Unofficial]
•Created by Woodside on 5/7/2023 in #fix-my-printer
X gantry has a "sine"-like resistance variance when moving along Y
I swapped with one of the Z motors and found it running out at the same spot. So I guess it must be the pulley. Hrmm.
15 replies
RRCRat Rig Community [Unofficial]
•Created by Woodside on 5/7/2023 in #fix-my-printer
X gantry has a "sine"-like resistance variance when moving along Y
I'm having a hard time being able to tell for sure, but looks like it may be the gear attached to the stepper not the stepper itself
15 replies
RRCRat Rig Community [Unofficial]
•Created by Woodside on 5/7/2023 in #fix-my-printer
X gantry has a "sine"-like resistance variance when moving along Y
I was gonna diagnose that today, ran out of time last night
15 replies
RRCRat Rig Community [Unofficial]
•Created by Woodside on 5/7/2023 in #fix-my-printer
X gantry has a "sine"-like resistance variance when moving along Y
Though that runout doesn't seem correlated with the varying resistance
15 replies
RRCRat Rig Community [Unofficial]
•Created by Woodside on 5/7/2023 in #fix-my-printer
X gantry has a "sine"-like resistance variance when moving along Y
I don't know how that even happened
15 replies
RRCRat Rig Community [Unofficial]
•Created by Woodside on 5/7/2023 in #fix-my-printer
X gantry has a "sine"-like resistance variance when moving along Y
It does appear one of my CoreXY steppers has maybe a half millimeter of runout. Is this a major problem?
15 replies