gywilo
RRCRat Rig Community [Unofficial]
•Created by gywilo on 9/6/2024 in #ratos-support
MCU shutdown; timer too close
Thanks, will do.
Which logs are applicable here and how do I find them?
6 replies
RRCRat Rig Community [Unofficial]
•Created by gywilo on 2/21/2024 in #fix-my-print
underextrusion- due to retraction?
I increased hot end temperature and issue appears to be resolved.
4 replies
RRCRat Rig Community [Unofficial]
•Created by gywilo on 2/21/2024 in #fix-my-print
underextrusion- due to retraction?
4 replies
RRCRat Rig Community [Unofficial]
•Created by gywilo on 10/29/2023 in #fix-my-print
over extrusion and under extrusion on the same print
I'm all for the dualrail mod. Keeps consistent Z distance offset. Quality over speed for me.
10 replies
RRCRat Rig Community [Unofficial]
•Created by gywilo on 10/29/2023 in #fix-my-print
over extrusion and under extrusion on the same print
10 replies
RRCRat Rig Community [Unofficial]
•Created by gywilo on 10/29/2023 in #fix-my-print
over extrusion and under extrusion on the same print
Hmmm, interesting, maybe the cause of the problem was different for you and me.
I've been able to resolve this issue, and am really happy with the top surface I am getting now.
I'm not exactly sure what actually fixed the issue, but I added the UHF nut to rapido, then re-tuned the printer, changing temps speeds and EM settings.
10 replies
RRCRat Rig Community [Unofficial]
•Created by gywilo on 10/29/2023 in #fix-my-print
over extrusion and under extrusion on the same print
I have already installed this mod and glad I did, didn't help here though.
10 replies
RRCRat Rig Community [Unofficial]
•Created by gywilo on 10/29/2023 in #fix-my-print
over extrusion and under extrusion on the same print
Could increasing speed or acceleration be the cause?
This is the 2nd print, the first one completed successfully and one of the few differences was speed and acceleration rates.
10 replies
RRCRat Rig Community [Unofficial]
•Created by gywilo on 10/12/2023 in #fix-my-print
layer cracking
For speed, how do you determine which to increase and by much?
11 replies
RRCRat Rig Community [Unofficial]
•Created by gywilo on 10/12/2023 in #fix-my-print
layer cracking
I increased temp to 235°C and that resolved layer cracking issue
11 replies
RRCRat Rig Community [Unofficial]
•Created by gywilo on 10/12/2023 in #fix-my-print
layer cracking
Normal default ratrig superslicer preconfigured. I think it's 100 mm/s and 3000mm/s/s
11 replies
RRCRat Rig Community [Unofficial]
•Created by gywilo on 10/12/2023 in #fix-my-print
layer cracking
I think I'm going to try again with hot end temp raised from 210-220 to 240°C
11 replies
RRCRat Rig Community [Unofficial]
•Created by gywilo on 10/12/2023 in #fix-my-print
layer cracking
The outter ends/edges are always complete.
11 replies
RRCRat Rig Community [Unofficial]
•Created by gywilo on 10/12/2023 in #fix-my-print
layer cracking
11 replies
RRCRat Rig Community [Unofficial]
•Created by gywilo on 9/14/2023 in #fix-my-print
ripping/tearing of first few layers in one local spot on large print.
dish soap
15 replies
RRCRat Rig Community [Unofficial]
•Created by gywilo on 9/14/2023 in #fix-my-print
ripping/tearing of first few layers in one local spot on large print.
70% IPA then soap and warm water
15 replies
RRCRat Rig Community [Unofficial]
•Created by gywilo on 9/14/2023 in #fix-my-print
ripping/tearing of first few layers in one local spot on large print.
I cleaned the build surface and that resolved the issue, able to print clean first layer in that spot now
15 replies
RRCRat Rig Community [Unofficial]
•Created by gywilo on 9/14/2023 in #fix-my-print
ripping/tearing of first few layers in one local spot on large print.
I will try cleaning with hot water and dish soap
15 replies
RRCRat Rig Community [Unofficial]
•Created by gywilo on 9/14/2023 in #fix-my-print
ripping/tearing of first few layers in one local spot on large print.
perhaps the surface has been contaminated in some way or the PEI coating was not applied correctly in this area?
15 replies
RRCRat Rig Community [Unofficial]
•Created by gywilo on 9/14/2023 in #fix-my-print
ripping/tearing of first few layers in one local spot on large print.
okay, so I've done two tests to confirm this is a not a bed mesh issue and instead something wrong with the surface itself.
1. I increased bed mesh density so that probeing occurs every 10mm, and still got same result.
2. I then went back to regular mesh density and rotated the bed surface 90° so that the problem area was in a different spot (back right instead back left)
15 replies