Serdar1976 Posts - Answer Overflow

Serdar1976

Posts Comments

RRCRat Rig Community [Unofficial]

•Created by Serdar1976 on 7/8/2024 in #german-support

Kollision beim starten vom Druck

91 replies

RRCRat Rig Community [Unofficial]

•Created by Serdar1976 on 6/29/2024 in #german-support

Z_TILT_ADJUST Z-Tilt Probleme beim Abfahren

37 replies

RRCRat Rig Community [Unofficial]

•Created by Serdar1976 on 6/27/2024 in #ratos-support

Triangellab Euclid: Shutdown due to expected probe state to be stowed but is deployed (0)

40 replies

RRCRat Rig Community [Unofficial]

•Created by Serdar1976 on 6/27/2024 in #german-support

Triangellab Euclid: Shutdown due to expected probe state to be stowed but is deployed (0)

78 replies

RRCRat Rig Community [Unofficial]

•Created by Serdar1976 on 6/25/2024 in #ratos-support

Euclid with brush Macro Configuration

Hello friends, I made the Euclid recording with Brush myself and wrote the code. Since I have only been working with configuration G-code for a few days, it does not work properly yet. When I trigger Brush Out Macro it goes out and with Brush in it goes in. When I press Probe load, the X & Y axis should be homed first, then the arm is extended and the Euclid is picked up. After picking up, the arm should be retracted again. With Probe Stow, I wanted the arm to extend, the Euclid to be brought into the park position, the separation to take place and then the arm to be retracted again. Can you help me with the macro?

6 replies

RRCRat Rig Community [Unofficial]

•Created by Serdar1976 on 6/24/2024 in #german-support

Fan Lüfter Steuern Printer.cfg

34 replies

RRCRat Rig Community [Unofficial]

•Created by Serdar1976 on 6/23/2024 in #ratos-support

Manta M8P v2 with cb1

Hello to all, I’m working on this trouble almost 3 days . Unfortunately, I can’t get it set up . Maybe one of you knows the solution for my problem . I running the Manta with the cb1 Unfortunately, the CB one is not booting up as long as I’m not plug-in. The jumper to the 5 V switch. I attached you to videos to explain my situation best as possible. I need help is highly appreciated . Best Regards Serdar

4 replies

RRCRat Rig Community [Unofficial]

•Created by Serdar1976 on 6/22/2024 in #german-support

M8P v2 mit CB1 und Ebb42 startet nicht

Hallo Freund, Ich brauch wieder eure Unterstützung. Ich hab hier ein Problem mit meinem Manta Board. . Es will nicht starten, ohne USB power Unterstützung . Wenn ich’s allein mit 24 V versorge, sehe ich am CB1 und am Manta Bord das Licht angehen aber die grüne LED, dass das CB1 Sport hochfährt und vom CB1 die Fan LED leuchtet nicht . Ich muss erst den PIN wieder reinstecken und zusätzlich über USB versorgen, damit das System hochfährt . Bin für jede Hilfe dankbar 🙏

3 replies

RRCRat Rig Community [Unofficial]

•Created by Serdar1976 on 5/11/2024 in #german-support

extrusion Ursache unklar

Hallo Freunde, in dem Video habe ich das Problem bestmöglich beschrieben. Ich bitte um eure Unterstützung gleich die Ursache wirklich nicht herausfinden konnte .

95 replies

RRCRat Rig Community [Unofficial]

•Created by Serdar1976 on 5/9/2024 in #german-support

Temperatur Probleme