spacebaby0695
RRCRat Rig Community [Unofficial]
•Created by spacebaby0695 on 10/27/2024 in #fix-my-printer
Heater fault
It's really strange. I can fidget with the wires at 240 and its fine. I'm thinking defective thermistor. Mine isn't the screw type so I'm not sure where to get one. RR customer service is awful and I don't to wait another 2-3 weeks for them to replace it
12 replies
RRCRat Rig Community [Unofficial]
•Created by spacebaby0695 on 10/27/2024 in #fix-my-printer
Heater fault
12 replies
RRCRat Rig Community [Unofficial]
•Created by spacebaby0695 on 10/27/2024 in #fix-my-printer
Heater fault
MCU 'toolboard_t1' shutdown: ADC out of range
Sensor 'extruder1' temperature 65707422.564 not in range 0.000:350.000
This generally occurs when a heater temperature exceeds
its configured min_temp or max_temp.
Once the underlying issue is corrected, use the
"FIRMWARE_RESTART" command to reset the firmware, reload the
config, and restart the host software.
Printer is shutdown
12 replies
RRCRat Rig Community [Unofficial]
•Created by spacebaby0695 on 10/27/2024 in #ratos-support
VAOC T1 x not lining up
Seems to be working again, thanks
58 replies
RRCRat Rig Community [Unofficial]
•Created by spacebaby0695 on 10/27/2024 in #ratos-support
VAOC T1 x not lining up
You're doing a lot, it happens
58 replies
RRCRat Rig Community [Unofficial]
•Created by spacebaby0695 on 10/27/2024 in #ratos-support
VAOC T1 x not lining up
I did the updates and now I'm getting this "Option 'gcode' in section 'gcode_macro VAOC' must be specified"
58 replies
RRCRat Rig Community [Unofficial]
•Created by spacebaby0695 on 10/27/2024 in #ratos-support
VAOC T1 x not lining up
I'll do that now, thanks
58 replies
RRCRat Rig Community [Unofficial]
•Created by spacebaby0695 on 10/27/2024 in #ratos-support
VAOC T1 x not lining up
I did the update and the first thiing I got was this " Error evaluating 'gcode_macro _START_VAOC:gcode': gcode.CommandError: Unexpected VAOC x-control point detected! Please run '_VAOC_RESET' to roll back to default values."
58 replies
RRCRat Rig Community [Unofficial]
•Created by spacebaby0695 on 10/27/2024 in #ratos-support
VAOC T1 x not lining up
Thanks, found it
58 replies
RRCRat Rig Community [Unofficial]
•Created by spacebaby0695 on 10/27/2024 in #ratos-support
VAOC T1 x not lining up
where do I find the static config? Is that the file that says ratos_varables
58 replies
RRCRat Rig Community [Unofficial]
•Created by spacebaby0695 on 10/27/2024 in #ratos-support
VAOC T1 x not lining up
mystery solved, it seems to be working now
58 replies
RRCRat Rig Community [Unofficial]
•Created by spacebaby0695 on 10/27/2024 in #ratos-support
VAOC T1 x not lining up
I kept getting that message and couldn't try again until I sent that command
58 replies
RRCRat Rig Community [Unofficial]
•Created by spacebaby0695 on 10/27/2024 in #ratos-support
VAOC T1 x not lining up
it was in an error message so I did _VAOC_RESET
58 replies
RRCRat Rig Community [Unofficial]
•Created by spacebaby0695 on 10/27/2024 in #ratos-support
VAOC T1 x not lining up
You wold think it would go back to default when doing a VAOC_reset
58 replies
RRCRat Rig Community [Unofficial]
•Created by spacebaby0695 on 10/27/2024 in #ratos-support
VAOC T1 x not lining up
Maybe I messed something up on my first try and it registered it 533 in the ratos_varables. Where the saved varables section you just posted
58 replies
RRCRat Rig Community [Unofficial]
•Created by spacebaby0695 on 10/27/2024 in #ratos-support
VAOC T1 x not lining up
It's set to 533 on the 500, I changed it to 531
58 replies
RRCRat Rig Community [Unofficial]
•Created by spacebaby0695 on 10/27/2024 in #ratos-support
VAOC T1 x not lining up
So I figured it out but leaving the post up for others. You can change the y control point under Ratrig varables. When the gantry was hitting the back it was moving the heads out of alignment. I think Ratrig should change the default y control point to something lower
58 replies
RRCRat Rig Community [Unofficial]
•Created by Anrot on 10/16/2024 in #fix-my-resonance
VC4 Idex Belts
I think this might have been mentioned but for me as soon as I put the lid on my problems went away. I think the way the umbilical cords are joined in the back they amplify one another. On the 500 the cords are pushed down by the lid dampening them. My graphs looked like your all's and I was ready to give up for the day when I did one last test with the lids. This is just my first day messing with it. I was mentioning the hybrid because it was tricky and the same techniques of listening to and watching the belts at the right frequency apply. At least on mine
1230 replies
RRCRat Rig Community [Unofficial]
•Created by Anrot on 10/16/2024 in #fix-my-resonance
VC4 Idex Belts
One thing that helped me tune the Hybrid was the excite axes feature in Shake-tune. You set the frequecy to where your problem is and you usally can hear it. I would then touch each belt to see wich was giving me problems. The realtime analyst in Rat OS pulses a little differenty. I can't hear it as well but sometimes I can see which belt is vibrating. Still wrapping my head around IDEX because it's not really a core xy anymore. Just x t0 and x t1 with a cartesian Y
1230 replies
RRCRat Rig Community [Unofficial]
•Created by Anrot on 10/16/2024 in #fix-my-resonance
VC4 Idex Belts
I'm guessing this is a 300 or 400mm build. I had awesome graphs with the Hybrid on my 500. IDEX is giving me a fit
1230 replies