shadyguido
RRCRat Rig Community [Unofficial]
•Created by shadyguido on 3/25/2024 in #fix-my-print
trying to print the fan duct in ASA
the youtubers are telling me it might just be heat building up in the part.
14 replies
RRCRat Rig Community [Unofficial]
•Created by shadyguido on 3/25/2024 in #fix-my-print
trying to print the fan duct in ASA
I'm starting to think the part is just too small to print at any reasonable speed. I need to slow down to a crawl
14 replies
RRCRat Rig Community [Unofficial]
•Created by shadyguido on 3/25/2024 in #fix-my-print
trying to print the fan duct in ASA
oh interesting. I will try that. To be clear it could also just be that I really need this part to make the cooling work correctly, right? The whole point is that the stock fan shroud isn't pointing low enough
14 replies
RRCRat Rig Community [Unofficial]
•Created by shadyguido on 3/25/2024 in #fix-my-print
trying to print the fan duct in ASA
Good eye! It's a 0.8 nozzle. Obviously not ideal for small prints like this one
14 replies
RRCRat Rig Community [Unofficial]
•Created by shadyguido on 3/21/2024 in #fix-my-print
VERY first blob of skirt won't stick
thanks @TheTik and @Max for your help!
11 replies
RRCRat Rig Community [Unofficial]
•Created by shadyguido on 3/21/2024 in #fix-my-print
VERY first blob of skirt won't stick
for those searching in the future: I fixed this issue handily by lowering both the temperature of the hotend and the bed. I had cranked up temps after switching to a 0.8 nozzle, but neglected to lower them for the first layer, where I wasn't extruding with much flow due to lower speeds. Also 70c (ratrig standard) is probably too hot for the bed
11 replies
RRCRat Rig Community [Unofficial]
•Created by shadyguido on 3/21/2024 in #fix-my-print
VERY first blob of skirt won't stick
OH you mean thickness. They are set to 0.4. Caliper is measuring closer to 0.3
11 replies
RRCRat Rig Community [Unofficial]
•Created by shadyguido on 3/21/2024 in #fix-my-print
VERY first blob of skirt won't stick
(and report back to reward you helpful souls with more buging
11 replies
RRCRat Rig Community [Unofficial]
•Created by shadyguido on 3/21/2024 in #fix-my-print
VERY first blob of skirt won't stick
I will give this a shot
11 replies
RRCRat Rig Community [Unofficial]
•Created by shadyguido on 3/21/2024 in #fix-my-print
VERY first blob of skirt won't stick
I have a 0.8 nozzle. Extrusion width is set to Auto. Isn't that thickness to be expected?
11 replies
RRCRat Rig Community [Unofficial]
•Created by shadyguido on 1/12/2024 in #fix-my-resonance
How do I look?
For future builders searching for a solution to a similar problem: My rear motor mounts were not tight, nor were the grub screws holding in the gears to the motors. I wrenched down everything. no more layer shift or diagonal leaning or any ohter keyword that might come up on a search 😉
24 replies
RRCRat Rig Community [Unofficial]
•Created by shadyguido on 1/12/2024 in #fix-my-resonance
How do I look?
Hah ok. Is one of the belts just too long?
24 replies
RRCRat Rig Community [Unofficial]
•Created by shadyguido on 1/12/2024 in #fix-my-resonance
How do I look?
completely
24 replies
RRCRat Rig Community [Unofficial]
•Created by shadyguido on 1/12/2024 in #fix-my-resonance
How do I look?
you think that had something to do with it? How?
24 replies
RRCRat Rig Community [Unofficial]
•Created by shadyguido on 1/12/2024 in #fix-my-resonance
How do I look?
I tied the shaper cable to the umbilical and took out the filament... maybe that did something?
24 replies
RRCRat Rig Community [Unofficial]
•Created by shadyguido on 1/12/2024 in #fix-my-resonance
How do I look?
24 replies
RRCRat Rig Community [Unofficial]
•Created by shadyguido on 1/12/2024 in #fix-my-resonance
How do I look?
24 replies
RRCRat Rig Community [Unofficial]
•Created by shadyguido on 1/12/2024 in #fix-my-resonance
How do I look?
I tightened a bit and here's what I got
24 replies
RRCRat Rig Community [Unofficial]
•Created by shadyguido on 1/12/2024 in #fix-my-resonance
How do I look?
hrm. any way to tell from the graphs whether they are tense enough? or which one is not tense enough?
24 replies
RRCRat Rig Community [Unofficial]
•Created by shadyguido on 1/12/2024 in #fix-my-resonance
How do I look?
or is that just a limitation of the motors? Or is it the steppers? I am totally stock - not even a fan blowing on the steppers
24 replies