koekie40
RRCRat Rig Community [Unofficial]
•Created by koekie40 on 11/6/2024 in #fix-my-printer
Connecting a fan 4028 to EBB V1.2 in RatOS
i solved it. it working now #################
FANS
###############################
Part cooling fan
[fan]
enable_pin: toolboard_t0:PD3
cycle_time: 0.00004
7 replies
RRCRat Rig Community [Unofficial]
•Created by koekie40 on 11/6/2024 in #fix-my-printer
Connecting a fan 4028 to EBB V1.2 in RatOS
red and black are in pin: PA1, is connected to the power ?
7 replies
RRCRat Rig Community [Unofficial]
•Created by koekie40 on 10/23/2024 in #fix-my-printer
Problem with config my hotend with EBB 42
i have found it, in started the Wizard i change the setting for the fans. thanks
15 replies
RRCRat Rig Community [Unofficial]
•Created by koekie40 on 10/23/2024 in #fix-my-printer
Problem with config my hotend with EBB 42
15 replies
RRCRat Rig Community [Unofficial]
•Created by koekie40 on 10/23/2024 in #fix-my-printer
Problem with config my hotend with EBB 42
if i look to ebb-42 wiring it is on PA2. if i look in RatOS.cfg it is fan_toolhead_cooling_pin=PA1,
15 replies
RRCRat Rig Community [Unofficial]
•Created by koekie40 on 10/23/2024 in #fix-my-printer
Problem with config my hotend with EBB 42
if i use the slicer bar in mainsail it works
15 replies
RRCRat Rig Community [Unofficial]
•Created by koekie40 on 10/23/2024 in #fix-my-printer
Problem with config my hotend with EBB 42
do i need to take it out in my config
15 replies
RRCRat Rig Community [Unofficial]
•Created by koekie40 on 10/23/2024 in #fix-my-printer
Problem with config my hotend with EBB 42
15 replies
RRCRat Rig Community [Unofficial]
•Created by koekie40 on 8/21/2024 in #ratos-support
i'm trying to install RatOS v2.1.0.rc2 on Pi 4 B
I have found it. It was the SD card. New U1 A1 solved it. Thanks for all your support in this.:chefkiss:
69 replies
RRCRat Rig Community [Unofficial]
•Created by koekie40 on 8/21/2024 in #ratos-support
i'm trying to install RatOS v2.1.0.rc2 on Pi 4 B
Have bought a new PI4 B but still have the same problem
69 replies
RRCRat Rig Community [Unofficial]
•Created by koekie40 on 8/21/2024 in #ratos-support
i'm trying to install RatOS v2.1.0.rc2 on Pi 4 B
Mikl, if i only install raspberry os 32 it works, if i install raspberry 32 with mainsail than i have the same issue. if i install Ratos V2.0.2 it works also.
69 replies
RRCRat Rig Community [Unofficial]
•Created by koekie40 on 8/21/2024 in #ratos-support
i'm trying to install RatOS v2.1.0.rc2 on Pi 4 B
69 replies
RRCRat Rig Community [Unofficial]
•Created by koekie40 on 8/21/2024 in #ratos-support
i'm trying to install RatOS v2.1.0.rc2 on Pi 4 B
is it possible to do this in ip 4 ?
69 replies
RRCRat Rig Community [Unofficial]
•Created by koekie40 on 8/21/2024 in #ratos-support
i'm trying to install RatOS v2.1.0.rc2 on Pi 4 B
Do I need to remove ipv6 in the router
69 replies
RRCRat Rig Community [Unofficial]
•Created by koekie40 on 8/21/2024 in #ratos-support
i'm trying to install RatOS v2.1.0.rc2 on Pi 4 B
69 replies
RRCRat Rig Community [Unofficial]
•Created by koekie40 on 8/21/2024 in #ratos-support
i'm trying to install RatOS v2.1.0.rc2 on Pi 4 B
this from moonraker log after i setp the wifi
69 replies
RRCRat Rig Community [Unofficial]
•Created by koekie40 on 8/21/2024 in #ratos-support
i'm trying to install RatOS v2.1.0.rc2 on Pi 4 B
What I don't understand is if I install RatOS v2.0.2 it goes fine no problem at all. What has changed about the setup after Ratos V2.0.2 to Ratos V2.1.0 after the wifi is found en connected.
69 replies
RRCRat Rig Community [Unofficial]
•Created by koekie40 on 8/21/2024 in #ratos-support
i'm trying to install RatOS v2.1.0.rc2 on Pi 4 B
is still the same issue.
69 replies
RRCRat Rig Community [Unofficial]
•Created by koekie40 on 8/21/2024 in #ratos-support
i'm trying to install RatOS v2.1.0.rc2 on Pi 4 B
ok i will try it
69 replies
RRCRat Rig Community [Unofficial]
•Created by koekie40 on 8/21/2024 in #ratos-support
i'm trying to install RatOS v2.1.0.rc2 on Pi 4 B
69 replies