Ju'
RRCRat Rig Community [Unofficial]
•Created by Lusn on 3/13/2024 in #fix-my-mesh
V-core 300 first mesh cold and hot
Hello,
I’m not an expert but you should take a look at this video : https://www.youtube.com/watch?v=h7ZTq2dDTkM&ab_channel=3DPrinters%26aWhiteboard
You should start by make your back plate corner flat. So in this case I would suggest you to lower B. It also seems that you have a bit of bowing on your X axis.
5 replies
RRCRat Rig Community [Unofficial]
•Created by Grimstod on 3/11/2024 in #fix-my-printer
Odd Z error
Hello,
It sounds like your probe catch the bed before klipper tells him to move up to detect it. Maybe Manually push it down a bit and see what happens ?
14 replies
RRCRat Rig Community [Unofficial]
•Created by Ju' on 3/9/2024 in #fix-my-mesh
Weird things on right Y axis
I've done that when I rebuilt the right Y rail, end it up by doing the left & right. I ordered a torque screw driver I tried my best with hands ...
But for .200mm variation, the bed isn't supposed to correct these ?
19 replies
RRCRat Rig Community [Unofficial]
•Created by Brandon on 3/10/2024 in #fix-my-print
ABS Prints Flawless, PETG is a Dumpster Fire
Hi,
I'm having a bunch of problems printing PETG, but on your side it's looks like your nozzle temp is too low. PrusaSlicer have different premade filament profile for PETG. They are using 235° / 240°C as nozzle temp and 80°C as bed temp.
Hope it helps !
24 replies
RRCRat Rig Community [Unofficial]
•Created by Ju' on 3/9/2024 in #fix-my-mesh
Weird things on right Y axis
@VisualTech48 I tried a bunch of things, got C & D flat but I'm always getting A & B probed at around .130mm getting a total variation of about .220mm. About what I've read in other posts it's kinda "okay".
But I can't get a consistant first layer, my nozzle is always close to touch the bed on A & B. Like if any correction where applied. But when I take a close look on Z steppers' while printing, I could see them move a bit trying to compensate.
When I let the printer go to the second layer I could here the nozzle touching the previous layer or just rip it off the bed resulting in a fail print.
I'm pretty new to bed leveling since all of my other printer are manual leveling style. I was pretty sure it was an hardware issue but now I not sure of it anymore.
I could give my printer.cfg if it could help ...
In any case, thanks for your help it's appreciated !
19 replies
RRCRat Rig Community [Unofficial]
•Created by Ju' on 3/9/2024 in #fix-my-mesh
Weird things on right Y axis
19 replies
RRCRat Rig Community [Unofficial]
•Created by Ju' on 3/9/2024 in #fix-my-mesh
Weird things on right Y axis
19 replies
RRCRat Rig Community [Unofficial]
•Created by Ju' on 3/9/2024 in #fix-my-mesh
Weird things on right Y axis
I can't find the right adjustement, maybe I'm doing something wrong ... Each time I rase A to get D up, C is plunging, so I raise B and D plunge in response ...
19 replies
RRCRat Rig Community [Unofficial]
•Created by Ju' on 3/9/2024 in #fix-my-mesh
Weird things on right Y axis
I'm constantly getting B higher than the rest of the plate. It should be at the same level than A, shouldn't it ?
19 replies
RRCRat Rig Community [Unofficial]
•Created by Ju' on 3/9/2024 in #fix-my-mesh
Weird things on right Y axis
19 replies
RRCRat Rig Community [Unofficial]
•Created by Ju' on 3/9/2024 in #fix-my-mesh
Weird things on right Y axis
This is what I've done, but unfortunately I've scratched the aluminum bar by overtighten some screws, had to rotate it by 90° which led to re-calibrate everything
19 replies