Mr.Robot
RRCRat Rig Community [Unofficial]
•Created by Mr.Robot on 6/5/2024 in #fix-my-printer
4028 stopped working
ok, I checked the voltages at the fan end and there was no continuity from the GND pin in PB11 to the fan.
I went to re-solder the connection and found that the wire was broken 1/2" inside the wire jacket so the original fan did not die the GND wire broke in the jacket and caused it to disconnect.
6 replies
RRCRat Rig Community [Unofficial]
•Created by Mr.Robot on 6/5/2024 in #fix-my-printer
4028 stopped working
i have re-crimped the PWM pin 3 times
6 replies
RRCRat Rig Community [Unofficial]
•Created by Mr.Robot on 6/5/2024 in #fix-my-printer
4028 stopped working
I have plugged another 12v fan into Fan7 and it works, and between fan7 and PB11 i have 12v when the fan it set to 50% power
6 replies
RRCRat Rig Community [Unofficial]
•Created by Mr.Robot on 11/1/2023 in #fix-my-printer
VC3.1 500 bed not heating
ok so i tested all the way and forth again and i must have missed it early but the thermal fuse shows no continuity so yeah figured that one out, thank gawd its not the whole mat that needs to be replaced.
12 replies
RRCRat Rig Community [Unofficial]
•Created by Mr.Robot on 11/1/2023 in #fix-my-printer
VC3.1 500 bed not heating
so ill have to make sure it contiues past that
12 replies
RRCRat Rig Community [Unofficial]
•Created by Mr.Robot on 11/1/2023 in #fix-my-printer
VC3.1 500 bed not heating
cuz i checked the fuse after requesting for the bed to heat and it showed 120v through it
12 replies
RRCRat Rig Community [Unofficial]
•Created by Mr.Robot on 11/1/2023 in #fix-my-printer
VC3.1 500 bed not heating
gunna have to tear it apart in the morning and check it all
12 replies
RRCRat Rig Community [Unofficial]
•Created by Mr.Robot on 11/1/2023 in #fix-my-printer
VC3.1 500 bed not heating
and the bed temp rises when i have the chamber heater on as well
12 replies
RRCRat Rig Community [Unofficial]
•Created by Mr.Robot on 11/1/2023 in #fix-my-printer
VC3.1 500 bed not heating
right now the bed is sitting at 16c in my shop when i tell it to go to 60c for example it'll jump to 16.5c- 16.7c but them drops again
12 replies
RRCRat Rig Community [Unofficial]
•Created by Mr.Robot on 11/1/2023 in #fix-my-printer
VC3.1 500 bed not heating
Thermistor is good pointed a hot air gun at the bed and temp went up
12 replies
RRCRat Rig Community [Unofficial]
•Created by Mr.Robot on 11/1/2023 in #fix-my-printer
VC3.1 500 bed not heating
ok so, edit the bed shows that when i send the command it looks as though its starting to heat up but only by like .5 of a degree
12 replies
RRCRat Rig Community [Unofficial]
•Created by Dante Tango on 10/8/2023 in #fix-my-printer
Bed Not Heating
psoted, but now a plot twist lol
18 replies
RRCRat Rig Community [Unofficial]
•Created by Dante Tango on 10/8/2023 in #fix-my-printer
Bed Not Heating
i send the command and then nothing happens
18 replies
RRCRat Rig Community [Unofficial]
•Created by Dante Tango on 10/8/2023 in #fix-my-printer
Bed Not Heating
Thermistor issue??
18 replies
RRCRat Rig Community [Unofficial]
•Created by Dante Tango on 10/8/2023 in #fix-my-printer
Bed Not Heating
but the odd part is it reads 120V across the fuse
18 replies
RRCRat Rig Community [Unofficial]
•Created by Dante Tango on 10/8/2023 in #fix-my-printer
Bed Not Heating
VC 3.1 500 so a 120V 1600W pad
18 replies
RRCRat Rig Community [Unofficial]
•Created by Dante Tango on 10/8/2023 in #fix-my-printer
Bed Not Heating
what kind of thermal fuse does it need
18 replies
RRCRat Rig Community [Unofficial]
•Created by R34Pr on 9/3/2023 in #fix-my-resonance
VC3.1 + Enclosure 2.0 Belt Tension & Shaper Graphs
Helps get you close, print two place one on each belt and try and aim for the middle of the dial
23 replies
RRCRat Rig Community [Unofficial]
•Created by R34Pr on 9/3/2023 in #fix-my-resonance
VC3.1 + Enclosure 2.0 Belt Tension & Shaper Graphs
Or this little beauty
23 replies
RRCRat Rig Community [Unofficial]
•Created by R34Pr on 9/3/2023 in #fix-my-resonance
VC3.1 + Enclosure 2.0 Belt Tension & Shaper Graphs
23 replies