uzi 🇦🇹
RRCRat Rig Community [Unofficial]
•Created by wombi on 1/13/2025 in #german-support
Linear Wagen schmieren bei Vcore4, Schluss mit dem Gequietsche, jedenfalls von den Linearführungen
Mit der Pressol fettpresse hab ich meine vorm Einbau geschmoert
3 replies
RRCRat Rig Community [Unofficial]
•Created by uzi 🇦🇹 on 12/6/2024 in #fix-my-printer
Noisy and jamming y rails after installing titanium tube
Ja ich hab hier alle möglichen channels geentert und dann hat mich Helge drauf aufmerksam gemacht. Der Typ ist vom Wissen eine chorifee und meinte er hat schon von so was gehört
37 replies
RRCRat Rig Community [Unofficial]
•Created by uzi 🇦🇹 on 12/6/2024 in #fix-my-printer
Noisy and jamming y rails after installing titanium tube
Kein Problem. Ich hoffe ich konnte dir helfen
37 replies
RRCRat Rig Community [Unofficial]
•Created by uzi 🇦🇹 on 12/6/2024 in #fix-my-printer
Noisy and jamming y rails after installing titanium tube
Probiers mal.
37 replies
RRCRat Rig Community [Unofficial]
•Created by uzi 🇦🇹 on 12/6/2024 in #fix-my-printer
Noisy and jamming y rails after installing titanium tube
37 replies
RRCRat Rig Community [Unofficial]
•Created by uzi 🇦🇹 on 12/6/2024 in #fix-my-printer
Noisy and jamming y rails after installing titanium tube
Denke auch das da nicht viel um sein wird
37 replies
RRCRat Rig Community [Unofficial]
•Created by uzi 🇦🇹 on 12/6/2024 in #fix-my-printer
Noisy and jamming y rails after installing titanium tube
Je nach Charge sind die verschieden
37 replies
RRCRat Rig Community [Unofficial]
•Created by uzi 🇦🇹 on 12/6/2024 in #fix-my-printer
Noisy and jamming y rails after installing titanium tube
Keine Ahnung ob die passt
37 replies
RRCRat Rig Community [Unofficial]
•Created by uzi 🇦🇹 on 12/6/2024 in #fix-my-printer
Noisy and jamming y rails after installing titanium tube
Ja ist aber eine thinkercad Vorlage mit einen 20,25 mal 20,04-07 rohr
37 replies
RRCRat Rig Community [Unofficial]
•Created by uzi 🇦🇹 on 12/6/2024 in #fix-my-printer
Noisy and jamming y rails after installing titanium tube
37 replies
RRCRat Rig Community [Unofficial]
•Created by uzi 🇦🇹 on 12/6/2024 in #fix-my-printer
Noisy and jamming y rails after installing titanium tube
37 replies
RRCRat Rig Community [Unofficial]
•Created by uzi 🇦🇹 on 12/6/2024 in #fix-my-printer
Noisy and jamming y rails after installing titanium tube
37 replies
RRCRat Rig Community [Unofficial]
•Created by uzi 🇦🇹 on 12/6/2024 in #fix-my-printer
Noisy and jamming y rails after installing titanium tube
I think my tube is twisted an not straight
I can't manage to adjust the rails and the ends so that it runs flawlessly. I printed a form for measuring but unfortunately I have to print it again. Helge gave the tip. But it looks like this and I'll print it again I just know I can't print it like that. I'll give up on titanium and stick with aluminum before I get into the unsolvable problems. Maybe I'll ask if he takes it back. I'm currently trying to install the normal extrusion again. I'm a bit disappointed with the tube if it really isn't 100% straight and given the length that makes a difference. Unfortunately, this is a tube and not a milled or ground material. He would have to have that reworked at spannsysteme, for example. I'll see what the gauges say tomorrow
37 replies
RRCRat Rig Community [Unofficial]
•Created by uzi 🇦🇹 on 12/6/2024 in #fix-my-printer
Noisy and jamming y rails after installing titanium tube
37 replies
RRCRat Rig Community [Unofficial]
•Created by uzi 🇦🇹 on 12/6/2024 in #fix-my-printer
Noisy and jamming y rails after installing titanium tube
@tg73
37 replies
RRCRat Rig Community [Unofficial]
•Created by uzi 🇦🇹 on 12/6/2024 in #fix-my-printer
Noisy and jamming y rails after installing titanium tube
I have loosened the screws on the gantry several times and loosened everything on the Y rails, the carriages too, and then adjusted the rails again, even though they were already there. I'm starting to despair because everything was great and I was convinced. Were my printed parts not good? I put a 0.1mm shim on top of the M5 because the tube protrudes. Maybe print them again? The Allen key in the screws will soon be broken. It still doesn't run smoothly and if I loosen a holder on a carriage it runs on its own and as soon as I fasten it it no longer runs. Can anyone help us here? Have you never had problems like this? You designed and tested them, didn't you?
@Mike-Toro3D
37 replies
RRCRat Rig Community [Unofficial]
•Created by NutellaBrot155 on 12/22/2023 in #fix-my-printer
Loud rail sounds
Yes, you could be right. I used extra end brackets with more play, but it could be that the position is not right. But it does sound scratchy when only one side is fixed and the other is completely loose. In the extrusion, the rail can only move slightly sideways. But I can try it, but I think that the pipe is also clamped too tightly.
10 replies
RRCRat Rig Community [Unofficial]
•Created by NutellaBrot155 on 12/22/2023 in #fix-my-printer
Loud rail sounds
Yes, unfortunately I let myself be tempted to change the rail and it was already perfect before. That's why the Y rails should fit. So should I adjust them again?
10 replies
RRCRat Rig Community [Unofficial]
•Created by NutellaBrot155 on 12/22/2023 in #fix-my-printer
Loud rail sounds
Hello. How did you solve the problem back then?
10 replies
RRCRat Rig Community [Unofficial]
•Created by uzi 🇦🇹 on 9/2/2024 in #fix-my-print
Minion in Heated Chamber, Asa Problems with Edges
4 replies