ds makes⚡
RRCRat Rig Community [Unofficial]
•Created by ds makes⚡ on 6/17/2023 in #fix-my-printer
strange behaviour of my vcore
You could be right ,I shall lower them down to standard .
11 replies
RRCRat Rig Community [Unofficial]
•Created by ds makes⚡ on 6/17/2023 in #fix-my-printer
strange behaviour of my vcore
Thank you for all your inputs much appreciated.
I have been running this machine for over a year with no problems my homing speeds are usually 750mm/s and I am running 2209s cooled it's seems to start up like this and after a few homes goes away and then runs fine.
As you can see from the video the homing is all over the please and it even attempts to pickup the euclid in the middle of the bed so it was out of sync.
I have been running the steppers at 1.8 so maybe I have over done them but everything has been running fine but just lately the weather in the UK as been hotter than usual.
Thanks again
11 replies
RRCRat Rig Community [Unofficial]
•Created by ds makes⚡ on 5/24/2023 in #ratos-support
Adaptive mesh
oh right i get it now thank you for clearing that up for me much appreciated .
6 replies
RRCRat Rig Community [Unofficial]
•Created by ds makes⚡ on 5/24/2023 in #ratos-support
Adaptive mesh
also is the prime location supposed to change pending on the area probe?
6 replies
RRCRat Rig Community [Unofficial]
•Created by ds makes⚡ on 5/24/2023 in #ratos-support
Adaptive mesh
for some reason the slicer start gcode had got messed up lol ,sorry
6 replies
RRCRat Rig Community [Unofficial]
•Created by ds makes⚡ on 5/21/2023 in #ratos-support
moonraker warnings
Superb thanks again
25 replies
RRCRat Rig Community [Unofficial]
•Created by ds makes⚡ on 5/21/2023 in #ratos-support
moonraker warnings
yes that looks to have sorted it,thank you
25 replies
RRCRat Rig Community [Unofficial]
•Created by ds makes⚡ on 5/21/2023 in #ratos-support
moonraker warnings
Updating RatOS device symlinks..
###### Updating whitelisted commands
###### Updating service permissions
###### Installing beacon module...
/home/pi /home/pi
Cloning into 'beacon'...
remote: Enumerating objects: 29, done.
remote: Counting objects: 100% (29/29), done.
remote: Compressing objects: 100% (25/25), done.
remote: Total 29 (delta 13), reused 17 (delta 4), pack-reused 0
Receiving objects: 100% (29/29), 34.59 KiB | 1.73 MiB/s, done.
Resolving deltas: 100% (13/13), done.
/home/pi
beacon: installing python requirements to env.
Looking in indexes: https://pypi.org/simple, https://www.piwheels.org/simple
Requirement already satisfied: numpy>=1.16.6 in ./klippy-env/lib/python3.9/site-packages (from -r /home/pi/beacon/requirements.txt (line 2)) (1.23.4)
beacon: registering beacon with the configurator.
###### Registering klippy extension 'beacon' with the RatOS Configurator...
{"id":null,"result":{"type":"data","data":{"json":true}}}Registered beacon successfully.
###### Installing git hooks
###### Registering klippy extension 'ratos_homing_extension' with the RatOS Configurator...
{"id":null,"result":{"type":"data","data":{"json":true}}}Registered ratos_homing_extension successfully.
###### Symlinking klippy extensions
Symlinked 4/4 extension(s):
Symlink for "gcode_shell_command.py" already exists
Symlink for "linear_movement_vibrations.py" already exists
Symlink for "ratos_homing.py" already exists
Symlink for "beacon.py" created
###### Symlinking moonraker extensions
Symlinked 1/1 extension(s):
Symlink for "timelapse.py" already exists
25 replies
RRCRat Rig Community [Unofficial]
•Created by ds makes⚡ on 5/21/2023 in #ratos-support
moonraker warnings
here you go Mikl
25 replies
RRCRat Rig Community [Unofficial]
•Created by ds makes⚡ on 5/21/2023 in #ratos-support
moonraker warnings
Sorry I shall have to do this tomorrow as I'm not at the printer .
I shall get back to you thank you for your help
25 replies
RRCRat Rig Community [Unofficial]
•Created by ds makes⚡ on 5/21/2023 in #ratos-support
moonraker warnings
No not at all buddy
25 replies
RRCRat Rig Community [Unofficial]
•Created by ds makes⚡ on 5/21/2023 in #ratos-support
moonraker warnings
No worries I have a euclid installed
25 replies
RRCRat Rig Community [Unofficial]
•Created by ds makes⚡ on 5/21/2023 in #ratos-support
moonraker warnings
Not installed at all it just come up a few nights ago after updating ratos
25 replies
RRCRat Rig Community [Unofficial]
•Created by ds makes⚡ on 4/23/2023 in #fix-my-resonance
Belt tension looks noisy
I noticed whilst doing the shaper calibration that the euclid probe was rattling against the cooling duct but I can't remember whether it was when it was doing the X or y axis .
I shall try again tonight thank you
8 replies
RRCRat Rig Community [Unofficial]
•Created by ds makes⚡ on 4/23/2023 in #fix-my-resonance
Belt tension looks noisy
8 replies
RRCRat Rig Community [Unofficial]
•Created by ds makes⚡ on 4/23/2023 in #fix-my-resonance
Belt tension looks noisy
right i have been playing about with the belts again and have checked the belt routing and check over the rails and that they are aligned but as you will see the the belt are looking slightly better but the shaper on Y is not so good. I not really good at interpreting these charts so any help gratefully appreciated thank you
8 replies
RRCRat Rig Community [Unofficial]
•Created by ds makes⚡ on 4/23/2023 in #fix-my-resonance
Belt tension looks noisy
8 replies
RRCRat Rig Community [Unofficial]
•Created by ds makes⚡ on 2/22/2023 in #fix-my-printer
my v minion is noise
That's what I did I commented the uncooled section and uncommented the cooled section
5 replies
RRCRat Rig Community [Unofficial]
•Created by ds makes⚡ on 2/15/2023 in #ratos-support
EBB36 v1.2 failing flashing when updating klipper
@miklschmidt well it definitely seems that it must of been the usb hub that was messing me about ,since have the pi 4 it has printed fine with no problems.
Thanks for your help much appreciated
7 replies
RRCRat Rig Community [Unofficial]
•Created by ds makes⚡ on 2/15/2023 in #ratos-support
EBB36 v1.2 failing flashing when updating klipper
Yes you could be right ,the pi 4 has arrived and is on the vcore and I redid the flashing to the octopus and the ebb36 and updated klipper in update manage with no problems.
Also run 2 prints without a hitch so far so looking good so far.
7 replies