ItsJesus
RRCRat Rig Community [Unofficial]
•Created by ItsJesus on 6/6/2024 in #ratos-support
Is it possible to edit board-definition.json (SKR 3 pin definition error)
Will do! Thanks for the help
15 replies
RRCRat Rig Community [Unofficial]
•Created by ItsJesus on 6/6/2024 in #ratos-support
Is it possible to edit board-definition.json (SKR 3 pin definition error)
I'll send a picture of the error once I get back to my pc.
15 replies
RRCRat Rig Community [Unofficial]
•Created by ItsJesus on 6/6/2024 in #ratos-support
Is it possible to edit board-definition.json (SKR 3 pin definition error)
X UART should be PD5
15 replies
RRCRat Rig Community [Unofficial]
•Created by ItsJesus on 6/6/2024 in #ratos-support
Is it possible to edit board-definition.json (SKR 3 pin definition error)
Referencing the above from BTT Github
15 replies
RRCRat Rig Community [Unofficial]
•Created by ItsJesus on 6/6/2024 in #ratos-support
Is it possible to edit board-definition.json (SKR 3 pin definition error)
15 replies
RRCRat Rig Community [Unofficial]
•Created by ItsJesus on 6/6/2024 in #ratos-support
Is it possible to edit board-definition.json (SKR 3 pin definition error)
PE0 is assigned to X UART and CS when it should only be assigned to Z enable
15 replies
RRCRat Rig Community [Unofficial]
•Created by ItsJesus on 3/5/2024 in #ratos-support
remote access/port forwarding
Will do.
4 replies
RRCRat Rig Community [Unofficial]
•Created by gywilo on 10/12/2023 in #fix-my-print
layer cracking
Trial and error seemed to work fine. I just printed a model a few times and changed as needed.
11 replies
RRCRat Rig Community [Unofficial]
•Created by gywilo on 10/12/2023 in #fix-my-print
layer cracking
I arbitrarily increased mine. Started at 200, tried 400, reduced due to defects to 300, reduced to 200
11 replies
RRCRat Rig Community [Unofficial]
•Created by gywilo on 10/12/2023 in #fix-my-print
layer cracking
You can 100% speed that up. Use accel speed from your resonance graphs, and I set my base speed at 200 mm/s
11 replies
RRCRat Rig Community [Unofficial]
•Created by Animatrix on 10/9/2023 in #fix-my-printer
y axis skipping at accel > 5k (V-core 3.1 500)
I had the same issue and would advise you to stop printing as you risk the belt snapping (mine did)
109 replies
RRCRat Rig Community [Unofficial]
•Created by gywilo on 10/12/2023 in #fix-my-print
layer cracking
What speed and acceleration were you printing at?
11 replies
RRCRat Rig Community [Unofficial]
•Created by ItsJesus on 9/11/2023 in #fix-my-printer
Delta 4 pin fan not working
updated config file
6 replies
RRCRat Rig Community [Unofficial]
•Created by ItsJesus on 9/11/2023 in #fix-my-printer
Delta 4 pin fan not working
I recently ordered a box of JST XH connectors, I will attempt to recrimp on Thursday. Otherwise, if anyone has any ideas please let me know.
6 replies
RRCRat Rig Community [Unofficial]
•Created by ItsJesus on 9/11/2023 in #fix-my-printer
Delta 4 pin fan not working
Attached is the config file I am currently running
6 replies
RRCRat Rig Community [Unofficial]
•Created by ItsJesus on 9/8/2023 in #fix-my-printer
Various homing related issues
Quite possible, that's what I was thinking. Once im done with what I'm doing I will verify the stepper wiring.
25 replies
RRCRat Rig Community [Unofficial]
•Created by ItsJesus on 9/8/2023 in #fix-my-printer
Various homing related issues
I am getting a repeated Z Tilt Adjust error of
Retries aborting: Probed points range is increasing.
This is happening after 10 retries of the probed points, all of which have been consitantly out of range
25 replies