Luigivaba
RRCRat Rig Community [Unofficial]
•Created by Luigivaba on 3/28/2024 in #fix-my-printer
Move out of range despite no move out of range in G-Code
4 replies
RRCRat Rig Community [Unofficial]
•Created by Luigivaba on 1/22/2024 in #fix-my-printer
Communication loss to DS18B20
My printer just stopped because it lost communication with the DS18B20. The sensor is just used to check homogenity of chamber temperature, can the printer be configured to ignore the communication loss and carry on? If these sensors are that unreliable I am not comfortible to use them on the pi. Can they be attached to i.e. the octopus or an arduino nano? DS18_report_time: was default, so 3.
5 replies
RRCRat Rig Community [Unofficial]
•Created by Luigivaba on 1/6/2024 in #german-support
Octopus kann nicht mit TMC5160 Treibern Kommunizieren.
7 replies
RRCRat Rig Community [Unofficial]
•Created by Luigivaba on 1/2/2024 in #german-support
Drucker akzeptiert wiederverwendung existierender Pins nicht:
2 replies
RRCRat Rig Community [Unofficial]
•Created by Luigivaba on 8/1/2023 in #ratos-support
Printer cannot find raspi cameras
7 replies
RRCRat Rig Community [Unofficial]
•Created by Luigivaba on 7/31/2023 in #german-support
Drucker Mesht grundsätzlich ganzes Bed
Custom "Start print" macro ist jetzt gelöscht, alles Funktioniert jetzt mit den Standard RatOS macros. Allerdings mesht der Drucker jetzt das gesamte Druckbed vor jedem Druck. Slicer ist korrekt Configuriert und ich habe:
RESPOND MSG={params.X0}
RESPOND MSG={params.X1}
RESPOND MSG={params.Y0}
RESPOND MSG={params.Y1}
Verwendet um mir bestätigen zu lassen, dass der Slicer die Daten korrekt eingibt (Hatte dazu das "Start print macro" kurz kopiert und zwischenzeitlich wieder gelöscht). Es ist:
variable_calibrate_bed_mesh: True
variable_nozzle_priming: "primeblob"
Wie krieg ich ihn jetzt dazu nur das zu kalibrieren was gebraucht wird?
8 replies
RRCRat Rig Community [Unofficial]
•Created by Luigivaba on 7/31/2023 in #german-support
MCU 'mcu' shutdown: Timer too close
5 replies
RRCRat Rig Community [Unofficial]
•Created by Luigivaba on 6/28/2023 in #german-support
Drucker stürtzt bei zu lange drücken ab
75 replies
RRCRat Rig Community [Unofficial]
•Created by Luigivaba on 6/17/2023 in #fix-my-printer
Printer running into negative values due to mesh calculation
17 replies
RRCRat Rig Community [Unofficial]
•Created by Luigivaba on 4/14/2023 in #ratos-support
CB1 4B adapter Crashes immediately after startup
Hello, so I have flashed the following image onto my CB1 SD card: "2023-04-11-RatOS-v2.0.1-armbian-CB1.img.xz" and started it up. Shows RatOS, can also connect via Ethernet but crashes instantly with the green LED going blinking and has to be power supply resetted. There is a 4010 blowing onto the chips however the heatsinks will arrive next Tuesday so the chips are naked rn. Is it feasible that the device overheats or is there a different error going on?
87 replies
RRCRat Rig Community [Unofficial]
•Created by Luigivaba on 3/18/2023 in #ratos-support
Installed RatOs on a Pi2B and an SKR V1.4 (lpc1768): No Klipper
not sure whether anyone can help (or anything at this point) but:
Installed RatOs on a Pi2B and an SKR V1.4 and...
/dev/serial/by-id/usb-Klipper_lpc1768_11C0000AA39C48AF40D3395DC72000F5-if00
So the two find each other, however on the main page: Connection with Moonraker is there however it cant connect to klipper.
Firmware of the SKR also goes into Firmwar.cur so seems to flas correctly. Anyone any Idea what I could try?
47 replies