Andyc
RRCRat Rig Community [Unofficial]
•Created by Andyc on 6/4/2024 in #ratos-support
RatOS2.1 hotend fan pin swap not working
lol I dont get it either... but going to leave well alone as its working, Thanks for you help
30 replies
RRCRat Rig Community [Unofficial]
•Created by Andyc on 6/4/2024 in #ratos-support
RatOS2.1 hotend fan pin swap not working
yes part cooling is now working and hot end cooling too, still a little confused as my part cooling is on a different port on the octopus as i shorted and killed the original but i dont have the pin switch line in printer.cfg but it still works
30 replies
RRCRat Rig Community [Unofficial]
•Created by Andyc on 6/4/2024 in #ratos-support
RatOS2.1 hotend fan pin swap not working
30 replies
RRCRat Rig Community [Unofficial]
•Created by Andyc on 6/4/2024 in #ratos-support
RatOS2.1 hotend fan pin swap not working
well thats strange, Ive been heating extruder to 50 deg to start the fan running so I dont burn myself, after the last try I realised I'd left it heating, so switched extruder off, after a few minutes it had cooled so turned fan off and fan starts up! switch on heating and fan go's off, let it cool and it starts up........
30 replies
RRCRat Rig Community [Unofficial]
•Created by Andyc on 6/4/2024 in #ratos-support
RatOS2.1 hotend fan pin swap not working
Hi Mikl, Ok so ran through above instructions, updated a few things, deleted fan overide in printer.cfg , noted the fan was set to octopus v1.1 and not toolboard so changed this and rebooted, and its still not running, so here's my debug.zip file
30 replies
RRCRat Rig Community [Unofficial]
•Created by Andyc on 6/4/2024 in #ratos-support
RatOS2.1 hotend fan pin swap not working
I still cant get the hotend fan to work after the v2.1 upgrade, its a 24v fan plugged into PA2 on an ebb42 board, also tried it in PA1 as thats the one listed in ratos.cfg file under the [board_pins toolboard_t0] General pins section but neither of these get any voltage when the dashboard shows the Toolhead cooling fan as being on
30 replies
RRCRat Rig Community [Unofficial]
•Created by Andyc on 6/4/2024 in #ratos-support
RatOS2.1 hotend fan pin swap not working
Re run the configurator and fixed the fan, now works correctly, still no hotend fan though, will look again tomorrow night and see whats stopping that running , Many thanks again for your help. Goodnight
30 replies
RRCRat Rig Community [Unofficial]
•Created by Andyc on 6/4/2024 in #ratos-support
RatOS2.1 hotend fan pin swap not working
"Digitial PWM on 2-pin port" has 2 options octopus v1.1 and EBB42 V1.2 T0, Ive got the octopus one selected, or has it seen what I have now and selected it for me ?
30 replies
RRCRat Rig Community [Unofficial]
•Created by Andyc on 6/4/2024 in #ratos-support
RatOS2.1 hotend fan pin swap not working
So your saying I got click happy and didnt read the instructions........Guilty as charged.... as usual
30 replies
RRCRat Rig Community [Unofficial]
•Created by Andyc on 6/4/2024 in #ratos-support
RatOS2.1 hotend fan pin swap not working
Part cooling fan is running all the time.... but if I put the slider control up is slows down, seems to be reversed control ,100% on the slider is off 0% is max
30 replies
RRCRat Rig Community [Unofficial]
•Created by Andyc on 6/4/2024 in #ratos-support
RatOS2.1 hotend fan pin swap not working
Ok thanks, I have another problem then as I have no hotend fan, and hotends now in bits clearing the clog....
30 replies
RRCRat Rig Community [Unofficial]
•Created by Andyc on 2/25/2024 in #ratos-support
I loose camera's during printing
Ok Many thanks
12 replies
RRCRat Rig Community [Unofficial]
•Created by Andyc on 2/25/2024 in #ratos-support
I loose camera's during printing
A reboot of the pi is required to get the feed back again, a firmware restart does not do it
12 replies
RRCRat Rig Community [Unofficial]
•Created by Andyc on 2/25/2024 in #ratos-support
I loose camera's during printing
Ok Here's the logfile, just lost the nozzlecam feed, Frozen image in the display with both cams showing, If I switch to the nozzle cam only view I get nothing
12 replies
RRCRat Rig Community [Unofficial]
•Created by genetic-orange on 11/14/2023 in #ratos-support
Lots of corruption/dirty
raspberry
31 replies
RRCRat Rig Community [Unofficial]
•Created by lost on 9/27/2023 in #fix-my-print
Extrusion issues after retraction
Care to explain why and what you changed?
10 replies
RRCRat Rig Community [Unofficial]
•Created by frozen-sapphire on 10/2/2023 in #ratos-support
Weird communication issues out of nowhere
@miklschmidt The connection problems I was having have been solved by a new EBB42 board, Whilst waiting for it to arrive Ive also done a complete rewire and fitted an electrical panel ( was all screwed to a piece of plywood when first built) Ive have tried to get things running with the old EBB but was still getting disconnect issues, swapped to the new one now its arrived and it all works fine so far.
183 replies
RRCRat Rig Community [Unofficial]
•Created by ambitious-aqua on 10/2/2023 in #ratos-support
Weird communication issues out of nowhere
checked all the wiring and pins in the plugs onto the toolboard multiple times, all seem ok , I'm still thinking I might have a dry solder joint on the toolboard usb socket, but its printed a part so gona leave it alone ! the more I play and modify the more I break things.....
183 replies
RRCRat Rig Community [Unofficial]
•Created by eastern-cyan on 10/2/2023 in #ratos-support
Weird communication issues out of nowhere
but i i placed a finger on the socket it would error even though the plug was tightly mounted
183 replies
RRCRat Rig Community [Unofficial]
•Created by sensitive-blue on 10/2/2023 in #ratos-support
Weird communication issues out of nowhere
yes good and tight
183 replies