DanSX
RRCRat Rig Community [Unofficial]
•Created by DanSX on 1/23/2025 in #ratos-support
Pi Camera on New RatOS
5 replies
RRCRat Rig Community [Unofficial]
•Created by unwilling-turquoise on 7/23/2023 in #german-support
Drucker bleibt an beliebigen Stellen im Druck stehen
Hast du bei dir ein Display am Drucker?
15 replies
RRCRat Rig Community [Unofficial]
•Created by dependent-tan on 4/27/2023 in #german-support
Eva lässt sich nur nach links rechts bewegen und nicht nach vorne hinten
Sicher dass du die Riemen korrekt durch gezogen hast?
33 replies
RRCRat Rig Community [Unofficial]
•Created by subsequent-cyan on 4/16/2023 in #german-support
Wlan
Hast du dich denn mit dem RatOs "WLAN" verbunden?
22 replies
RRCRat Rig Community [Unofficial]
•Created by elliott on 3/7/2023 in #fix-my-mesh
What adjustments do I need to make?
I would try right Back Corner Up.
6 replies
RRCRat Rig Community [Unofficial]
•Created by DanSX on 2/7/2023 in #ratos-support
How to save an Import the Gcode and Progress before Update to RatOs 2.0
Good Idea :). Will try that the next days.
25 replies
RRCRat Rig Community [Unofficial]
•Created by DanSX on 2/7/2023 in #ratos-support
How to save an Import the Gcode and Progress before Update to RatOs 2.0
OK, but this only works when you still have the old system. The moonraker File alone of my old printer is not enough?
25 replies
RRCRat Rig Community [Unofficial]
•Created by DanSX on 2/7/2023 in #ratos-support
How to save an Import the Gcode and Progress before Update to RatOs 2.0
Yes this is what I tried.
25 replies
RRCRat Rig Community [Unofficial]
•Created by DanSX on 3/6/2023 in #fix-my-print
Bad Surface with holes
OK, thank you. Had this suspect.
4 replies
RRCRat Rig Community [Unofficial]
•Created by DanSX on 2/7/2023 in #ratos-support
How to save an Import the Gcode and Progress before Update to RatOs 2.0
That explains why it do not work...
There is no possibility to get it on a 64 Bit Version?
25 replies
RRCRat Rig Community [Unofficial]
•Created by DanSX on 2/7/2023 in #ratos-support
How to save an Import the Gcode and Progress before Update to RatOs 2.0
OK was RatOs 1.2.4 32 Bit?
And it dont work because now I use a 64 Bit Version?
25 replies
RRCRat Rig Community [Unofficial]
•Created by extended-salmon on 2/23/2023 in #fix-my-printer
TMC 'extruder' reports error: GSTAT: 00000001 reset=1(Reset)
I had this too.
First changed cable and Driver. At the end In changed the Motor, which fixed it.
6 replies
RRCRat Rig Community [Unofficial]
•Created by SimonSolar2C on 3/5/2023 in #fix-my-printer
XY axis scale wrong
Why you do not adjust it in the Slicer?
3 replies
RRCRat Rig Community [Unofficial]
•Created by DanSX on 2/7/2023 in #ratos-support
How to save an Import the Gcode and Progress before Update to RatOs 2.0
I updated my first printer today. The Import of the History so not Work. I tried it again with data of my second printer.
25 replies
RRCRat Rig Community [Unofficial]
•Created by Proof on 2/25/2023 in #german-support
Extruder Probleme
Welche Temperatur benutzt du denn beim 100mm/s? PlA?
26 replies
RRCRat Rig Community [Unofficial]
•Created by Proof on 2/25/2023 in #german-support
Extruder Probleme
Bei meinem LGX Extruder haben sich mal Innen die Zahnräder verschoben, wie weiß ich nicht. Nachdem ich ihn auf und wieder zu gemacht habe ging jedenfalls alles wieder. Weiß nicht ob beim Orbiter so was auch passieren kann.
26 replies
RRCRat Rig Community [Unofficial]
•Created by Proof on 2/25/2023 in #german-support
Extruder Probleme
Würde das Kabel fast ausschließen. Mein V Core reagiert da so sensibel drauf. Habe in den 3000h Druckzeit eltiche male Kabel getauscht weil die wohl irgendwo ein leichtes Kontaktproblem hatten. Was aber dann immer sofort in einer Fehlermeldung endet.
Wie sieht es denn aus wenn man den Extruder entspannt und das Filament mal von Hand durch schiebt?
26 replies
RRCRat Rig Community [Unofficial]
•Created by DanSX on 2/7/2023 in #ratos-support
How to save an Import the Gcode and Progress before Update to RatOs 2.0
OK moonraker Database I found.
25 replies
RRCRat Rig Community [Unofficial]
•Created by DanSX on 2/7/2023 in #ratos-support
How to save an Import the Gcode and Progress before Update to RatOs 2.0
@miklschmidt
Thank you. But at Gcode I can Not Download all, allways only one?
And where I finde the Database Backup for moonraker?
25 replies
RRCRat Rig Community [Unofficial]
•Created by DanSX on 2/5/2023 in #german-support
TMC Extruder Overtemp
Das letzte mal hatte ich ähnliche Probleme aber nur mit Gstat, da war der Motor kaputt. Jetzt tausche ich den als nächstes und dann mal schauen.
12 replies