Anrot
RRCRat Rig Community [Unofficial]
•Created by Anrot on 11/18/2024 in #fix-my-printer
VAOC calibration gives error: Move out of range
but im also not able to move the T1 to anywhere with same error ist this because of the x offset which is to big?
105 replies
RRCRat Rig Community [Unofficial]
•Created by Anrot on 11/18/2024 in #fix-my-printer
VAOC calibration gives error: Move out of range
ok
105 replies
RRCRat Rig Community [Unofficial]
•Created by Anrot on 11/18/2024 in #fix-my-printer
VAOC calibration gives error: Move out of range
I tried the do input shaping before I have to disasamble the printer again which gives me another error:
Move out of range: -61.194 248.570 17.000 [0.000]
105 replies
RRCRat Rig Community [Unofficial]
•Created by Anrot on 11/18/2024 in #fix-my-printer
VAOC calibration gives error: Move out of range
ok I will try these suggestions
105 replies
RRCRat Rig Community [Unofficial]
•Created by Anrot on 11/18/2024 in #fix-my-printer
VAOC calibration gives error: Move out of range
ok, this is bad new thank you
105 replies
RRCRat Rig Community [Unofficial]
•Created by Anrot on 11/18/2024 in #fix-my-printer
VAOC calibration gives error: Move out of range
105 replies
RRCRat Rig Community [Unofficial]
•Created by Anrot on 11/18/2024 in #fix-my-printer
VAOC calibration gives error: Move out of range
I did this doesn't work again
105 replies
RRCRat Rig Community [Unofficial]
•Created by Anrot on 11/18/2024 in #fix-my-printer
VAOC calibration gives error: Move out of range
[dual_carriage]
position_max: 559.916
position_endstop: 559.916
[gcode_macro RatOS]
variable_bed_margin_x: [60.000, 59.916]
[gcode_macro _VAOC]
variable_expected_camera_x_position: 214.051
variable_expected_camera_y_position: 522.609
[gcode_macro T0]
variable_parking_position: -58.000
[gcode_macro T1]
variable_parking_position: 557.916
105 replies
RRCRat Rig Community [Unofficial]
•Created by Anrot on 11/18/2024 in #fix-my-printer
VAOC calibration gives error: Move out of range
I mean in the printer.cfg the there then will be two times the variable:
[dual_carriage]
position_max:
105 replies
RRCRat Rig Community [Unofficial]
•Created by Anrot on 11/18/2024 in #fix-my-printer
VAOC calibration gives error: Move out of range
to clarify the standard values should be kept in so there will be two times :
[dual_carriage]
position_max:
position_endstop:
105 replies
RRCRat Rig Community [Unofficial]
•Created by Anrot on 11/18/2024 in #fix-my-printer
VAOC calibration gives error: Move out of range
Should i real just copy and past it as it is or overwrite the old values?
105 replies
RRCRat Rig Community [Unofficial]
•Created by Anrot on 11/18/2024 in #fix-my-printer
VAOC calibration gives error: Move out of range
ok sorry didn't know i have to change them again
105 replies
RRCRat Rig Community [Unofficial]
•Created by Anrot on 11/18/2024 in #fix-my-printer
VAOC calibration gives error: Move out of range
105 replies
RRCRat Rig Community [Unofficial]
•Created by Anrot on 11/18/2024 in #fix-my-printer
VAOC calibration gives error: Move out of range
Same error.
The sensor is just a little bit not as is looks like on the picture
105 replies
RRCRat Rig Community [Unofficial]
•Created by Anrot on 11/18/2024 in #fix-my-printer
VAOC calibration gives error: Move out of range
105 replies
RRCRat Rig Community [Unofficial]
•Created by Anrot on 11/18/2024 in #fix-my-printer
VAOC calibration gives error: Move out of range
but thats what the software gave me
105 replies
RRCRat Rig Community [Unofficial]
•Created by Anrot on 11/18/2024 in #fix-my-printer
VAOC calibration gives error: Move out of range
I did fill in the other values where ther was already one thats why they are not all on at the same place
105 replies
RRCRat Rig Community [Unofficial]
•Created by Anrot on 11/18/2024 in #fix-my-printer
VAOC calibration gives error: Move out of range
105 replies
RRCRat Rig Community [Unofficial]
•Created by Anrot on 11/18/2024 in #fix-my-printer
VAOC calibration gives error: Move out of range
But I did this minutes before?
105 replies
RRCRat Rig Community [Unofficial]
•Created by Anrot on 11/18/2024 in #fix-my-printer
VAOC calibration gives error: Move out of range
@Helge Keck but now i get this error when trying to print:
Error evaluating 'gcode_macro START_PRINT:gcode': gcode.CommandError: Toolhead x-offset is too high for the available parking space. Calibrate your X and DC endstop positions and make sure you stay below 1mm.
105 replies