K2Van CR-6 & Vcore 3.1 500 IDEX
RRCRat Rig Community [Unofficial]
•Created by K2Van CR-6 & Vcore 3.1 500 IDEX on 10/28/2024 in #ratos-support
Homing and "move exceeds maximum extrusion" errors after a canceled print.
I will probably not be able to follow up for next week as I travel to China, upon return I will check.
5 replies
RRCRat Rig Community [Unofficial]
•Created by K2Van CR-6 & Vcore 3.1 500 IDEX on 10/28/2024 in #ratos-support
Homing and "move exceeds maximum extrusion" errors after a canceled print.
Sorry for the delay but this is the output of the test print untill it was canceled and the output of a follow-up print.
5 replies
RRCRat Rig Community [Unofficial]
•Created by K2Van CR-6 & Vcore 3.1 500 IDEX on 10/6/2024 in #ratos-support
1 cm shift after pause
I was pausing to put magnets in. So just pause - resume, no other operations in RatOS.
15 replies
RRCRat Rig Community [Unofficial]
•Created by K2Van CR-6 & Vcore 3.1 500 IDEX on 10/6/2024 in #ratos-support
1 cm shift after pause
No it doesn't matter manual pause once the first layer has started is enough to avoid the shift.
15 replies
RRCRat Rig Community [Unofficial]
•Created by K2Van CR-6 & Vcore 3.1 500 IDEX on 10/6/2024 in #ratos-support
1 cm shift after pause
I will experiment a bit more as it seems like the initial manual pause needs to be after the first layer for it to work, will let you know.
15 replies
RRCRat Rig Community [Unofficial]
•Created by K2Van CR-6 & Vcore 3.1 500 IDEX on 10/6/2024 in #ratos-support
1 cm shift after pause
I found a work-around: when pausing manually the shift does not happen. The subsequent shift upon layer change from the slicer does not shift eighter then.
15 replies
RRCRat Rig Community [Unofficial]
•Created by K2Van CR-6 & Vcore 3.1 500 IDEX on 10/6/2024 in #ratos-support
1 cm shift after pause
I thought I might have a work-aroud: Pause it on layer 1 so it makes the shift before even starting the print but unfortunately that didn't work, it still shifts 1 cm on the next pause.
15 replies
RRCRat Rig Community [Unofficial]
•Created by K2Van CR-6 & Vcore 3.1 500 IDEX on 10/6/2024 in #ratos-support
1 cm shift after pause
Interesting is that this shift only happens upon the first pause. Had it pause 3 times now and only the first one shifted by 1 cm, the others are perfectly on top of that 1 cm shift, no additional shift any more.
15 replies
RRCRat Rig Community [Unofficial]
•Created by K2Van CR-6 & Vcore 3.1 500 IDEX on 10/6/2024 in #ratos-support
1 cm shift after pause
I disabled [exclude_objects] in the firmware as well as in the slicer the label objects.
15 replies
RRCRat Rig Community [Unofficial]
•Created by K2Van CR-6 & Vcore 3.1 500 IDEX on 10/6/2024 in #ratos-support
1 cm shift after pause
Nope, still the same result.
15 replies
RRCRat Rig Community [Unofficial]
•Created by K2Van CR-6 & Vcore 3.1 500 IDEX on 10/6/2024 in #ratos-support
1 cm shift after pause
15 replies
RRCRat Rig Community [Unofficial]
•Created by K2Van CR-6 & Vcore 3.1 500 IDEX on 2/11/2024 in #fix-my-resonance
V-core 500 IDEX terrible Y axis while X axis is quite OK
I found that i had some play in the X carriages which was OK for the X but not Y.
6 replies
RRCRat Rig Community [Unofficial]
•Created by K2Van CR-6 & Vcore 3.1 500 IDEX on 2/11/2024 in #fix-my-resonance
V-core 500 IDEX terrible Y axis while X axis is quite OK
And maybe one piece of info: I upgrade to 5160T PRO and 48V on all 4 x and y motors.
6 replies
RRCRat Rig Community [Unofficial]
•Created by K2Van CR-6 & Vcore 3.1 500 IDEX on 2/11/2024 in #fix-my-resonance
V-core 500 IDEX terrible Y axis while X axis is quite OK
6 replies
RRCRat Rig Community [Unofficial]
•Created by K2Van CR-6 & Vcore 3.1 500 IDEX on 2/11/2024 in #fix-my-resonance
V-core 500 IDEX terrible Y axis while X axis is quite OK
6 replies