Ouchmaster
RRCRat Rig Community [Unofficial]
•Created by Ouchmaster on 11/5/2024 in #ratos-support
How to upgrade from ratos 1.2 to 2.2 ?
Thanks will do then
6 replies
RRCRat Rig Community [Unofficial]
•Created by Ouchmaster on 2/5/2024 in #fix-my-print
Large print warping issue
Thank you. It helps rule out tuning issues. Many thanks
4 replies
RRCRat Rig Community [Unofficial]
•Created by Ouchmaster on 10/30/2023 in #ratos-support
Moonraker is not permitted to restart service 'RatOS'.
you ar eright, I see there was the V2 release...not in a rush to update, my rig is working very well as is
6 replies
RRCRat Rig Community [Unofficial]
•Created by Ouchmaster on 10/30/2023 in #ratos-support
Moonraker is not permitted to restart service 'RatOS'.
May thanks.
Thats weird though since I regularly accept incoming updates on my printer
6 replies
RRCRat Rig Community [Unofficial]
•Created by Ouchmaster on 8/28/2023 in #fix-my-printer
heating shuts if 1 second after prime line
Or will check the wires. Many thanks
3 replies
RRCRat Rig Community [Unofficial]
•Created by Ouchmaster on 8/16/2023 in #fix-my-resonance
Spikes at high mghz belt tension
Sorry missed your reponse. Running af 76 herz for both belts for months now. How do you know it is too tight by looking at that chart ?
4 replies
RRCRat Rig Community [Unofficial]
•Created by Ouchmaster on 2/27/2023 in #fix-my-printer
Heater disconnected from heating block
Nevermind found it
8 replies
RRCRat Rig Community [Unofficial]
•Created by Ouchmaster on 2/27/2023 in #fix-my-printer
Heater disconnected from heating block
8 replies
RRCRat Rig Community [Unofficial]
•Created by Ouchmaster on 2/27/2023 in #fix-my-printer
Heater disconnected from heating block
8 replies
RRCRat Rig Community [Unofficial]
•Created by Ouchmaster on 2/27/2023 in #fix-my-printer
Heater disconnected from heating block
Thank you. But how do i screw on the new part ? See old one has 3 screw holes
8 replies
RRCRat Rig Community [Unofficial]
•Created by Ouchmaster on 2/17/2023 in #fix-my-printer
occasional layer shift / Belt shifting
Ok thanks
54 replies
RRCRat Rig Community [Unofficial]
•Created by Ouchmaster on 2/17/2023 in #fix-my-printer
occasional layer shift / Belt shifting
One last question. When experiencing a layer shift, is there a way to rectify the situation during the print ? I mean pause the print and adjuste the printhead position back to where it is meant to be ?
54 replies
RRCRat Rig Community [Unofficial]
•Created by Ouchmaster on 2/17/2023 in #fix-my-printer
occasional layer shift / Belt shifting
Thanks will try that
54 replies
RRCRat Rig Community [Unofficial]
•Created by Ouchmaster on 2/17/2023 in #fix-my-printer
occasional layer shift / Belt shifting
Thanks again and have a good day ahead
54 replies
RRCRat Rig Community [Unofficial]
•Created by Ouchmaster on 2/17/2023 in #fix-my-printer
occasional layer shift / Belt shifting
Print is almost done and no more belt shifting
54 replies
RRCRat Rig Community [Unofficial]
•Created by Ouchmaster on 2/17/2023 in #fix-my-printer
occasional layer shift / Belt shifting
Aaaand a grub screw was indeed loose...screwed it back firmly on the flat surface of the stepper rod
54 replies
RRCRat Rig Community [Unofficial]
•Created by Ouchmaster on 2/17/2023 in #fix-my-printer
occasional layer shift / Belt shifting
Pressure advance was too high, ultimately creating blobs. Reduced PA
54 replies
RRCRat Rig Community [Unofficial]
•Created by Ouchmaster on 2/17/2023 in #fix-my-printer
occasional layer shift / Belt shifting
Nozzle base was leaking, creating blobs. Replaced and tigthened a new nozzle. No more blobs
54 replies
RRCRat Rig Community [Unofficial]
•Created by Ouchmaster on 2/17/2023 in #fix-my-printer
occasional layer shift / Belt shifting
Sorted out the issue, there was in fact 3 problems
54 replies
RRCRat Rig Community [Unofficial]
•Created by Ouchmaster on 2/17/2023 in #fix-my-printer
occasional layer shift / Belt shifting
Thank you for you kind support on that issue
54 replies