Diego
RRCRat Rig Community [Unofficial]
•Created by Diego on 6/3/2024 in #ratos-support
EXTRUDER OCTOPUS RATOS 2.1
The order colors is correct ?
32 replies
RRCRat Rig Community [Unofficial]
•Created by Diego on 6/3/2024 in #ratos-support
EXTRUDER OCTOPUS RATOS 2.1
I just put the tester on and it goes to 24v, it's fine
32 replies
RRCRat Rig Community [Unofficial]
•Created by Diego on 6/3/2024 in #ratos-support
EXTRUDER OCTOPUS RATOS 2.1
what? the cable usb c?
32 replies
RRCRat Rig Community [Unofficial]
•Created by Diego on 6/3/2024 in #ratos-support
EXTRUDER OCTOPUS RATOS 2.1
this is okey becose the heater works good
32 replies
RRCRat Rig Community [Unofficial]
•Created by Diego on 6/3/2024 in #ratos-support
EXTRUDER OCTOPUS RATOS 2.1
Most likely, I think I'll buy a sht36 v3 so I can update it a little 😉
32 replies
RRCRat Rig Community [Unofficial]
•Created by Diego on 6/3/2024 in #ratos-support
EXTRUDER OCTOPUS RATOS 2.1
i dont have canbus, i use the usb
32 replies
RRCRat Rig Community [Unofficial]
•Created by Diego on 6/3/2024 in #ratos-support
EXTRUDER OCTOPUS RATOS 2.1
only i have de 120r but i dont need no?
32 replies
RRCRat Rig Community [Unofficial]
•Created by Diego on 6/3/2024 in #ratos-support
EXTRUDER OCTOPUS RATOS 2.1
32 replies
RRCRat Rig Community [Unofficial]
•Created by Diego on 6/3/2024 in #ratos-support
EXTRUDER OCTOPUS RATOS 2.1
okey i check it
32 replies
RRCRat Rig Community [Unofficial]
•Created by Diego on 6/3/2024 in #ratos-support
EXTRUDER OCTOPUS RATOS 2.1
:sadpepe:
32 replies
RRCRat Rig Community [Unofficial]
•Created by Diego on 6/3/2024 in #ratos-support
EXTRUDER OCTOPUS RATOS 2.1
32 replies
RRCRat Rig Community [Unofficial]
•Created by Diego on 6/3/2024 in #ratos-support
EXTRUDER OCTOPUS RATOS 2.1
okey thx for the asnwer ❤️
32 replies
RRCRat Rig Community [Unofficial]
•Created by Diego on 6/3/2024 in #ratos-support
EXTRUDER OCTOPUS RATOS 2.1
I think it's better to cut the cables and put it in the toolhead...
32 replies
RRCRat Rig Community [Unofficial]
•Created by Diego on 6/3/2024 in #ratos-support
EXTRUDER OCTOPUS RATOS 2.1
I bought the ratrig v core 3.1 second-hand and it came to me that it has the extruder on the board hahah
32 replies
RRCRat Rig Community [Unofficial]
•Created by Diego on 6/3/2024 in #fix-my-printer
Error sensorless homing Ratos 2.1
10 replies
RRCRat Rig Community [Unofficial]
•Created by Diego on 6/3/2024 in #fix-my-printer
Error sensorless homing Ratos 2.1
i found the error
10 replies
RRCRat Rig Community [Unofficial]
•Created by Diego on 6/3/2024 in #fix-my-printer
Error sensorless homing Ratos 2.1
Could the diag_pin be wrong?
10 replies
RRCRat Rig Community [Unofficial]
•Created by Diego on 6/3/2024 in #fix-my-printer
Error sensorless homing Ratos 2.1
Idk what is happening
10 replies
RRCRat Rig Community [Unofficial]
•Created by Diego on 6/3/2024 in #fix-my-printer
Error sensorless homing Ratos 2.1
10 replies
RRCRat Rig Community [Unofficial]
•Created by Diego on 4/5/2024 in #fix-my-mesh
bad bed mesh v core 3.0
Retries: 0/10 Probed points range: 0.175312 tolerance: 0.200000
11:40
Making the following Z adjustments:
stepper_z = -0.006149
stepper_z1 = 0.001816
stepper_z2 = -0.007457
11:40
probe at 130.000,110.000 is z=1.581633
11:40
probe at 130.000,110.000 is z=1.581945
11:40
probe at 130.000,110.000 is z=1.582883
11:40
probe at 60.000,240.000 is z=1.414133
11:40
probe at 60.000,240.000 is z=1.414445
11:40
probe at 60.000,240.000 is z=1.413195
11:40
probe at 240.000,240.000 is z=1.553508
11:40
probe at 240.000,240.000 is z=1.552883
11:40
probe at 240.000,240.000 is z=1.552258
11:40
probe at 240.000,30.000 is z=1.406633
11:40
probe at 240.000,30.000 is z=1.406633
11:40
probe at 240.000,30.000 is z=1.407570
11:39
probe at 60.000,30.000 is z=1.527883
11:39
probe at 60.000,30.000 is z=1.527883
11:39
probe at 60.000,30.000 is z=1.527883
19 replies