3DBoomer
RRCRat Rig Community [Unofficial]
•Created by SgtKiLLx on 1/31/2025 in #fix-my-printer
Fresh install of RatOS - internal errors.
104 replies
RRCRat Rig Community [Unofficial]
•Created by SgtKiLLx on 1/31/2025 in #fix-my-printer
Fresh install of RatOS - internal errors.
Hey guys, I've been on the same issue for a week now. On an Mk3 setup : https://discord.com/channels/582187371529764864/1334134184738029629/1334134184738029629
104 replies
RRCRat Rig Community [Unofficial]
•Created by 3DBoomer on 1/29/2025 in #ratos-support
Internal error on command:"G28"
Error message, so tried refresh available updates, tried soft recovery and .... failed again
71 replies
RRCRat Rig Community [Unofficial]
•Created by 3DBoomer on 1/29/2025 in #ratos-support
Internal error on command:"G28"
71 replies
RRCRat Rig Community [Unofficial]
•Created by 3DBoomer on 1/29/2025 in #ratos-support
Internal error on command:"G28"
Ok : I did a complete check with Ratos Doctor followig this thread : https://discord.com/channels/582187371529764864/1330240060519616512/1330522101215658128
71 replies
RRCRat Rig Community [Unofficial]
•Created by 3DBoomer on 1/29/2025 in #ratos-support
Internal error on command:"G28"
71 replies
RRCRat Rig Community [Unofficial]
•Created by 3DBoomer on 1/29/2025 in #ratos-support
Internal error on command:"G28"
71 replies
RRCRat Rig Community [Unofficial]
•Created by 3DBoomer on 1/29/2025 in #ratos-support
Internal error on command:"G28"
Thx again 😉
71 replies
RRCRat Rig Community [Unofficial]
•Created by 3DBoomer on 1/29/2025 in #ratos-support
Internal error on command:"G28"
OK, in no specific order then. I'll go step by step to be on the safe side
71 replies
RRCRat Rig Community [Unofficial]
•Created by 3DBoomer on 1/29/2025 in #ratos-support
Internal error on command:"G28"
Would you advise any specific order for the following updates ?
71 replies
RRCRat Rig Community [Unofficial]
•Created by 3DBoomer on 1/29/2025 in #ratos-support
Internal error on command:"G28"
Ahhhhh.. Thanks man ! For being here and for the answer 🙂
71 replies
RRCRat Rig Community [Unofficial]
•Created by 3DBoomer on 1/29/2025 in #ratos-support
Internal error on command:"G28"
I then tried to update just moonraker, waited, rebooted, still no ratos-configurator in the list. I'm going nuts, I've been on this all week now.
71 replies
RRCRat Rig Community [Unofficial]
•Created by 3DBoomer on 1/29/2025 in #ratos-support
Internal error on command:"G28"
71 replies
RRCRat Rig Community [Unofficial]
•Created by 3DBoomer on 1/29/2025 in #ratos-support
Internal error on command:"G28"
71 replies
RRCRat Rig Community [Unofficial]
•Created by 3DBoomer on 1/29/2025 in #ratos-support
Internal error on command:"G28"
Thx guys 😉 we'll let them reflect on life philosophy and the importance of updates and upgrades all night and will try to go further in the morning.
May the Force be with you.
71 replies
RRCRat Rig Community [Unofficial]
•Created by 3DBoomer on 1/29/2025 in #ratos-support
Internal error on command:"G28"
71 replies
RRCRat Rig Community [Unofficial]
•Created by 3DBoomer on 1/29/2025 in #ratos-support
Internal error on command:"G28"
71 replies
RRCRat Rig Community [Unofficial]
•Created by 3DBoomer on 1/29/2025 in #ratos-support
Internal error on command:"G28"
No impact, even tried rebooting every 30' or so...
71 replies
RRCRat Rig Community [Unofficial]
•Created by 3DBoomer on 1/29/2025 in #ratos-support
Internal error on command:"G28"
71 replies
RRCRat Rig Community [Unofficial]
•Created by 3DBoomer on 1/29/2025 in #ratos-support
Internal error on command:"G28"
Both rasps I'm currently trying have been running Ratos 2.0.2 for a while on wifi, same network (Same Unify relays, using just the 2.4 ghz SSID)
71 replies