RyeRye
RyeRye
RRCRat Rig Community [Unofficial]
Created by RyeRye on 10/22/2024 in #fix-my-resonance
VC4-400 Initial Core XY graph
I'm just following the guide. These graphs are just coreXY belts. Next is adding hybrids.
21 replies
RRCRat Rig Community [Unofficial]
Created by RyeRye on 10/22/2024 in #fix-my-resonance
VC4-400 Initial Core XY graph
Thanks, I haven't tried the pluck method. I think next is adding hybrid belts before I start any test prints. Also adding enclosure now that it has arrived.
21 replies
RRCRat Rig Community [Unofficial]
Created by RyeRye on 10/22/2024 in #fix-my-resonance
VC4-400 Initial Core XY graph
Then yeah tensioning much more than I initially anticipated.
21 replies
RRCRat Rig Community [Unofficial]
Created by RyeRye on 10/22/2024 in #fix-my-resonance
VC4-400 Initial Core XY graph
Found that the clamps on the front of the toolhead were slipping. I didnt have enough belt in to start.
21 replies
RRCRat Rig Community [Unofficial]
Created by RyeRye on 10/22/2024 in #fix-my-resonance
VC4-400 Initial Core XY graph
No description
21 replies
RRCRat Rig Community [Unofficial]
Created by RyeRye on 10/22/2024 in #fix-my-resonance
VC4-400 Initial Core XY graph
No description
21 replies
RRCRat Rig Community [Unofficial]
Created by RyeRye on 10/22/2024 in #fix-my-resonance
VC4-400 Initial Core XY graph
No description
21 replies
RRCRat Rig Community [Unofficial]
Created by RyeRye on 10/21/2024 in #fix-my-mesh
Initial Preparation mesh
Also the beacon_ratos_calibrate needs bed heater installed. It stalled out when it came to that part.
15 replies
RRCRat Rig Community [Unofficial]
Created by RyeRye on 10/21/2024 in #fix-my-mesh
Initial Preparation mesh
No description
15 replies
RRCRat Rig Community [Unofficial]
Created by RyeRye on 10/21/2024 in #fix-my-mesh
Initial Preparation mesh
Now beacon_ratos_calibrate is working. Did touches and z tilt and now doing with extruder at temp. Will publish new mesh but I think this will fix it.
15 replies
RRCRat Rig Community [Unofficial]
Created by RyeRye on 10/21/2024 in #fix-my-mesh
Initial Preparation mesh
Thank you. Z1 and Z2 are flip flopped. Must have swapped wires at some point.
15 replies
RRCRat Rig Community [Unofficial]
Created by RyeRye on 10/21/2024 in #fix-my-mesh
Initial Preparation mesh
That’s what I ran and z tilt fails.
15 replies
RRCRat Rig Community [Unofficial]
Created by RyeRye on 10/21/2024 in #fix-my-mesh
Initial Preparation mesh
When it does z tilt it makes skew worse not better.
15 replies
RRCRat Rig Community [Unofficial]
Created by RyeRye on 10/21/2024 in #fix-my-mesh
Initial Preparation mesh
Doing z tilt now and it keeps failing.
15 replies
RRCRat Rig Community [Unofficial]
Created by omerk83 on 9/25/2024 in #ratos-support
RatOS wizard problems
Not entirely sure how much it matters but the documents tell you to take every other jumper off. To flash with RatOS 2.1 the only jumper should be USB power. If that fails the wizard walks you through DFU option where u temporarily add the boot jumper.
44 replies