SteveBorough
RRCRat Rig Community [Unofficial]
•Created by SteveBorough on 10/9/2024 in #ratos-support
RatOS 2 w/ Octopus Pro controller fan?
Hi, I'm using an Octopus Pro on my vCore3.1 and the latest RatOS release. By default what fan port should I use for the always-on board/steppers?
4 replies
RRCRat Rig Community [Unofficial]
•Created by SteveBorough on 4/25/2024 in #fix-my-printer
possible the latest updates borked Z Pinda detection?
Im getting head crashes every time i run a Z
6 replies
RRCRat Rig Community [Unofficial]
•Created by SteveBorough on 4/19/2024 in #fix-my-printer
Prints often fail at this Z height
4 replies
RRCRat Rig Community [Unofficial]
•Created by SteveBorough on 6/29/2023 in #ratos-support
Priming & Printing with .6 nozzle
Just switched to the Rapido .6 nozzle (changed extruder setting in config) and priming and printing is borked. Priming blob seems much smaller and doesnt stick to the bed, nozzle scrapes when starting print and print does not stick even slightly to the bed, most of the time it blobs around the nozzle. Had my .4 singing before this, please help
28 replies
RRCRat Rig Community [Unofficial]
•Created by SteveBorough on 6/7/2023 in #ratos-support
Fresh RatOS install Crowsnest broken
13 replies
RRCRat Rig Community [Unofficial]
•Created by SteveBorough on 5/31/2023 in #ratos-support
latest ratos update (5-31-23) throws error
Will send screenshot shortly
10 replies
RRCRat Rig Community [Unofficial]
•Created by SteveBorough on 5/28/2023 in #ratos-support
RatOS unstable since Crowsnest update
Left untouched for a few hours, camera is often unavailable and crowsnest needs to be restarted. In addition, sometimes the system goes offline and is unreachable (ssh, html, ping, etc...) Was rock solid before the latest updates
4 replies
RRCRat Rig Community [Unofficial]
•Created by SteveBorough on 5/24/2023 in #fix-my-mesh
Cant get this corner down
17 replies
RRCRat Rig Community [Unofficial]
•Created by SteveBorough on 5/19/2023 in #ratos-support
Native RatOS Adaptive Bed Mesh hits the bed in prime location
hope it didnt break my new Rapido, but it hit the bed on prime blob and I hit emergency stop luckily as it zoomed to start (why is that first jerk so fast?) Since adaptive mesh uses the Z-offset to dynamically transform the g-code, where is it pulling this value? I use PROBE_CALIBRATE to set my offset in my printer.cfg file
92 replies
RRCRat Rig Community [Unofficial]
•Created by SteveBorough on 5/7/2023 in #ratos-support
Primeline scrapes the bed
New v-core 3.1 default 400 with EBB42v1.2 & SKRAT, all looks well but primeline scrapes the bed (EMERGENCY STOP) this is after homing and mesh completes successfully. I set my Z offset using the paper method. Attaaching printer.cfg
11 replies
RRCRat Rig Community [Unofficial]
•Created by SteveBorough on 5/2/2023 in #ratos-support
v-core/Skrat/ebb42 overrides to get z1 &z2 working
RatRig advertises this config is possible so that’s what I bought and tried entering the stepper pins from the skrat manual (noting the 1 typo in the manual) into my override section but still only z0 moves, help please
12 replies