Peabutt
RRCRat Rig Community [Unofficial]
•Created by Peabutt on 12/15/2024 in #fix-my-printer
V4 idex z offset issue
I started with the idex commissioning. And because in no step it sais to assemble the heat and pei sheet, i decided to do it. I dont think my bed is defective, but i really do hope not now that i have everything glued. Honestly it looks like the gantry is out of plane. I havent had the time 2day, hopefully 2morrow
39 replies
RRCRat Rig Community [Unofficial]
•Created by Peabutt on 12/15/2024 in #fix-my-printer
V4 idex z offset issue
Now i need to make it as flat as possible and than ill try again
39 replies
RRCRat Rig Community [Unofficial]
•Created by Peabutt on 12/15/2024 in #fix-my-printer
V4 idex z offset issue
Not sure if it could have an impact on z offset but i dont think so
39 replies
RRCRat Rig Community [Unofficial]
•Created by Peabutt on 12/15/2024 in #fix-my-printer
V4 idex z offset issue
I discovered now that i have the gantry on an angle because bed mesh is twisted. The idex commissioning should cover all the steps but it doesnt
39 replies
RRCRat Rig Community [Unofficial]
•Created by Peabutt on 12/15/2024 in #fix-my-printer
V4 idex z offset issue
I did change the nozzle extender, and also the nozzles. Same results
39 replies
RRCRat Rig Community [Unofficial]
•Created by Peabutt on 12/15/2024 in #fix-my-printer
V4 idex z offset issue
Thanks again for the tips
39 replies
RRCRat Rig Community [Unofficial]
•Created by Peabutt on 12/15/2024 in #fix-my-printer
V4 idex z offset issue
Ill leave it as is. I want idex for dual filament. If i ever need copy/mirror mode ill think about it then
39 replies
RRCRat Rig Community [Unofficial]
•Created by Peabutt on 12/15/2024 in #fix-my-printer
V4 idex z offset issue
this is only important for copy and mirror mode right? for dual filament has no impact correct?
39 replies
RRCRat Rig Community [Unofficial]
•Created by Peabutt on 12/15/2024 in #fix-my-printer
V4 idex z offset issue
cant get any better without something as a spacer
39 replies
RRCRat Rig Community [Unofficial]
•Created by Peabutt on 12/15/2024 in #fix-my-printer
V4 idex z offset issue
39 replies
RRCRat Rig Community [Unofficial]
•Created by Peabutt on 12/15/2024 in #fix-my-printer
V4 idex z offset issue
39 replies
RRCRat Rig Community [Unofficial]
•Created by Peabutt on 12/15/2024 in #fix-my-printer
V4 idex z offset issue
39 replies
RRCRat Rig Community [Unofficial]
•Created by Peabutt on 12/15/2024 in #fix-my-printer
V4 idex z offset issue
i can try to tighten everything again on t0
39 replies
RRCRat Rig Community [Unofficial]
•Created by Peabutt on 12/15/2024 in #fix-my-printer
V4 idex z offset issue
t0 needs to go up correct?
39 replies
RRCRat Rig Community [Unofficial]
•Created by Peabutt on 12/15/2024 in #fix-my-printer
V4 idex z offset issue
yesterday
39 replies
RRCRat Rig Community [Unofficial]
•Created by Peabutt on 12/15/2024 in #fix-my-printer
V4 idex z offset issue
i disassembled both and assembled back again
39 replies
RRCRat Rig Community [Unofficial]
•Created by Peabutt on 12/15/2024 in #fix-my-printer
V4 idex z offset issue
i did that
39 replies
RRCRat Rig Community [Unofficial]
•Created by Peabutt on 12/15/2024 in #fix-my-printer
V4 idex z offset issue
still no good
39 replies
RRCRat Rig Community [Unofficial]
•Created by Peabutt on 12/15/2024 in #fix-my-printer
V4 idex z offset issue
39 replies
RRCRat Rig Community [Unofficial]
•Created by Peabutt on 12/15/2024 in #fix-my-printer
V4 idex z offset issue
Ill report back
39 replies