hhes
RRCRat Rig Community [Unofficial]
•Created by hhes on 10/18/2024 in #fix-my-printer
Z-Offset being ignored
I didn’t. I kinda assumed it was a bug introduced recently, because until that update everything worked fine for a few months
6 replies
RRCRat Rig Community [Unofficial]
•Created by hhes on 10/18/2024 in #fix-my-printer
Z-Offset being ignored
SAVE_Z_OFFSET before the print ends.6 replies
RRCRat Rig Community [Unofficial]
•Created by hhes on 10/15/2024 in #fix-my-print
External perimeter with no filament extruded after the seam and blobs everywhere
with 0.4 nozzle it prints perfectly fine. There's something about 0.6 nozzle profiles that makes it that way
18 replies
RRCRat Rig Community [Unofficial]
•Created by hhes on 10/15/2024 in #fix-my-print
External perimeter with no filament extruded after the seam and blobs everywhere
18 replies
RRCRat Rig Community [Unofficial]
•Created by hhes on 10/15/2024 in #fix-my-print
External perimeter with no filament extruded after the seam and blobs everywhere
Adjusted the extruder screw mid-print, maybe it wasn’t grippy enough. So far no improvement, though
18 replies
RRCRat Rig Community [Unofficial]
•Created by hhes on 10/15/2024 in #fix-my-print
External perimeter with no filament extruded after the seam and blobs everywhere
18 replies
RRCRat Rig Community [Unofficial]
•Created by hhes on 10/15/2024 in #fix-my-print
External perimeter with no filament extruded after the seam and blobs everywhere
Also, now I notice that the infill is also not looking good in a lot of places
18 replies
RRCRat Rig Community [Unofficial]
•Created by hhes on 10/15/2024 in #fix-my-print
External perimeter with no filament extruded after the seam and blobs everywhere
18 replies
RRCRat Rig Community [Unofficial]
•Created by hhes on 10/15/2024 in #fix-my-print
External perimeter with no filament extruded after the seam and blobs everywhere
Recalibrated the beacon and seems to be fine now, but the print is still off in the same spots. Some of the issues disappeared because I dried the filament
18 replies
RRCRat Rig Community [Unofficial]
•Created by hhes on 10/15/2024 in #fix-my-print
External perimeter with no filament extruded after the seam and blobs everywhere
I went the atomic way and changed the nozzle to another 0.6, this time from phaetus that was shipped with the hotend. now, however, it seems like I can't live adjust Z during the first layer test. Normally, after sending
SET_GCODE_OFFSET Z_ADJUST=-0.01 MOVE=1 the change would be reflected in a few seconds tops, but now no adjustments are made at all, even those sent on the very beginning of the print. I was checking was Klipper was reporting as the real Z coordinate, and my adjustments are 100% ignored. Any ideas what that might be? I tried restarting the printer (although I'm gonna do it again now)18 replies
RRCRat Rig Community [Unofficial]
•Created by hhes on 10/15/2024 in #fix-my-print
External perimeter with no filament extruded after the seam and blobs everywhere
I'm printing the same model with the flow limited to 20mm3/s, that's down from 40 from RatRig's profile and 25 from my own profile
18 replies
RRCRat Rig Community [Unofficial]
•Created by hhes on 10/15/2024 in #fix-my-print
External perimeter with no filament extruded after the seam and blobs everywhere
there was
18 replies
RRCRat Rig Community [Unofficial]
•Created by hhes on 10/15/2024 in #fix-my-print
External perimeter with no filament extruded after the seam and blobs everywhere
The first layer looks fine, I was looking at it as it was printed. As for the nozzle change -- I changed the nozzle recently to a V6 Diamondback 0.6mm. I used that nozzle before for PLA on this particular VC4, and on all kinds of filaments before that on Prusa MK3. It never happened with it before
18 replies
RRCRat Rig Community [Unofficial]
•Created by hhes on 10/15/2024 in #fix-my-print
External perimeter with no filament extruded after the seam and blobs everywhere
Also, PA is currently 0.015
18 replies
RRCRat Rig Community [Unofficial]
•Created by hhes on 7/9/2024 in #fix-my-print
[VC4 400] Pattern on the wall
16 replies
RRCRat Rig Community [Unofficial]
•Created by hhes on 7/9/2024 in #fix-my-print
[VC4 400] Pattern on the wall
@Cruz could this issue be connected with the one I had during the assembly? https://discord.com/channels/582187371529764864/1223286652949106748/1256655137439612990 should I send a support ticket?
16 replies
RRCRat Rig Community [Unofficial]
•Created by hhes on 7/9/2024 in #fix-my-print
[VC4 400] Pattern on the wall
Hm, you think it’s too loose?
16 replies
RRCRat Rig Community [Unofficial]
•Created by hhes on 7/9/2024 in #fix-my-print
[VC4 400] Pattern on the wall
I did temperature tower on this one and had best results at 205C
16 replies
RRCRat Rig Community [Unofficial]
•Created by hhes on 7/9/2024 in #fix-my-print
[VC4 400] Pattern on the wall
The PTFE tubes for sure are not causing any friction because they are free to move; I don’t use RR’s spool holder
16 replies
RRCRat Rig Community [Unofficial]
•Created by hhes on 7/9/2024 in #fix-my-print
[VC4 400] Pattern on the wall
This print was done on 0.025
16 replies