samus129
RRCRat Rig Community [Unofficial]
•Created by Skye on 1/23/2025 in #fix-my-printer
VC4 Part cooling fan will only run at 100%
Anyways man glad your up and running
42 replies
RRCRat Rig Community [Unofficial]
•Created by Skye on 1/23/2025 in #fix-my-printer
VC4 Part cooling fan will only run at 100%
Gotta take my x apart and install the TI bar and index head and wire both fans
42 replies
RRCRat Rig Community [Unofficial]
•Created by Skye on 1/23/2025 in #fix-my-printer
VC4 Part cooling fan will only run at 100%
Well glad it's working now 😁 I really wish I had the motivation to finish mine
42 replies
RRCRat Rig Community [Unofficial]
•Created by Skye on 1/23/2025 in #fix-my-printer
VC4 Part cooling fan will only run at 100%
I'm actually not sure sorry
42 replies
RRCRat Rig Community [Unofficial]
•Created by Skye on 1/23/2025 in #fix-my-printer
VC4 Part cooling fan will only run at 100%
Correct you will have to change it back. Wait did you try inverting the pin I think someone else had to do that 🤔
42 replies
RRCRat Rig Community [Unofficial]
•Created by Skye on 1/23/2025 in #fix-my-printer
VC4 Part cooling fan will only run at 100%
It will be at boot yes but that may be better than no speed control
42 replies
RRCRat Rig Community [Unofficial]
•Created by Skye on 1/23/2025 in #fix-my-printer
VC4 Part cooling fan will only run at 100%
Nope like in the guide online how the red and black go to the fan pins and pwm goes to the tool board is the default
42 replies
RRCRat Rig Community [Unofficial]
•Created by Skye on 1/23/2025 in #fix-my-printer
VC4 Part cooling fan will only run at 100%
did it working correctly with the default wiring that's in the quide?
42 replies
RRCRat Rig Community [Unofficial]
•Created by Skye on 1/9/2025 in #fix-my-resonance
vc4 500 core xy for now first resonance
59 replies
RRCRat Rig Community [Unofficial]
•Created by Skye on 1/9/2025 in #fix-my-resonance
vc4 500 core xy for now first resonance
59 replies
RRCRat Rig Community [Unofficial]
•Created by RyeRye on 10/22/2024 in #fix-my-resonance
VC4-400 Initial Core XY graph
For belts I went 1 tooth past the small indent so that when you push the grabber and it pulls the belt back a little it still has good grip
21 replies
RRCRat Rig Community [Unofficial]
•Created by RyeRye on 10/22/2024 in #fix-my-resonance
VC4-400 Initial Core XY graph
You probably also got a little bit of skew in your gantry but not much sorry for the late reply
21 replies
RRCRat Rig Community [Unofficial]
•Created by RyeRye on 10/22/2024 in #fix-my-resonance
VC4-400 Initial Core XY graph
To go back and tune the XY after your going to need to unplug the hybrid
21 replies
RRCRat Rig Community [Unofficial]
•Created by samus129 on 8/18/2024 in #fix-my-resonance
VCore 4 400 belt issue
let me know what you find
376 replies
RRCRat Rig Community [Unofficial]
•Created by samus129 on 8/18/2024 in #fix-my-resonance
VCore 4 400 belt issue
.9
376 replies
RRCRat Rig Community [Unofficial]
•Created by samus129 on 8/18/2024 in #fix-my-resonance
VCore 4 400 belt issue
when I torque them past 1NM the issue comes back so
376 replies
RRCRat Rig Community [Unofficial]
•Created by samus129 on 8/18/2024 in #fix-my-resonance
VCore 4 400 belt issue
on both sides
376 replies
RRCRat Rig Community [Unofficial]
•Created by samus129 on 8/18/2024 in #fix-my-resonance
VCore 4 400 belt issue
https://discord.com/channels/582187371529764864/1274541213638197351/1277025878936781063 those 4 bolts I move up and down were too tight
376 replies
RRCRat Rig Community [Unofficial]
•Created by samus129 on 8/18/2024 in #fix-my-resonance
VCore 4 400 belt issue
ya but mine was probally a one off
376 replies
RRCRat Rig Community [Unofficial]
•Created by Champ180 on 9/18/2024 in #ratos-support
limit speed
You try disabling performance mode in the confirmation steps?
10 replies