Jessica
Jessica
PostsComments
RRCRat Rig Community [Unofficial]
Created by rmilyard on 1/21/2025 in #fix-my-printer
IDEX 500 Orbiter V2 Smart Sensor issues.
Nothing about that code has anything to do with the print bed movement range.
40 replies
RRCRat Rig Community [Unofficial]
Created by rmilyard on 1/21/2025 in #fix-my-printer
IDEX 500 Orbiter V2 Smart Sensor issues.
I just prefer to have add ons as a separate cfg file so it doesn't get fully overwritten in the case that updates happen that rewrite printer.cfg.
40 replies
RRCRat Rig Community [Unofficial]
Created by rmilyard on 1/21/2025 in #fix-my-printer
IDEX 500 Orbiter V2 Smart Sensor issues.
If you had them reversed from what I did, yes, then your pin settings should be fine.
40 replies
RRCRat Rig Community [Unofficial]
Created by rmilyard on 1/21/2025 in #fix-my-printer
IDEX 500 Orbiter V2 Smart Sensor issues.
Yeah this is just my specific way of referencing all the RatRig values for the sensor. It's definitely not necessary to do it that way.
40 replies
RRCRat Rig Community [Unofficial]
Created by Jessica on 12/3/2024 in #fix-my-printer
Massive Layer shift after 2 hours
I'll leave this open until Friday once the new belt arrives and I can confirm it's good again
11 replies
RRCRat Rig Community [Unofficial]
Created by Jessica on 12/3/2024 in #fix-my-printer
Massive Layer shift after 2 hours
11 replies
RRCRat Rig Community [Unofficial]
Created by Jessica on 12/3/2024 in #fix-my-printer
Massive Layer shift after 2 hours
I just removed it entirely, flipped it's orientation and re-threaded it. Now the belt pulls down rather than up.
11 replies
RRCRat Rig Community [Unofficial]
Created by Jessica on 12/3/2024 in #fix-my-printer
Massive Layer shift after 2 hours
Looks like it's the belt itself
11 replies
RRCRat Rig Community [Unofficial]
Created by Jessica on 12/3/2024 in #fix-my-printer
Massive Layer shift after 2 hours
Ah it's not the bearing alignment
11 replies
RRCRat Rig Community [Unofficial]
Created by Jessica on 12/3/2024 in #fix-my-printer
Massive Layer shift after 2 hours
11 replies
RRCRat Rig Community [Unofficial]
Created by Jessica on 12/3/2024 in #fix-my-printer
Massive Layer shift after 2 hours
so it'll require some disassembly to fix
11 replies
RRCRat Rig Community [Unofficial]
Created by Jessica on 12/3/2024 in #fix-my-printer
Massive Layer shift after 2 hours
OK after some inspection, it seems there's a misaligned bearing on the lower left rear belt that's wearing the belt and I think periodically gets bound enough to stop the motor
11 replies
RRCRat Rig Community [Unofficial]
Created by 3DBoomer on 8/31/2024 in #ratos-support
2 in line extruders...
The built in command is SYNC_EXTRUDER_MOTION EXTRUDER=my_spool_extruder MOTION_QUEUE=extruder
22 replies
RRCRat Rig Community [Unofficial]
Created by 3DBoomer on 8/31/2024 in #ratos-support
2 in line extruders...
You shouldn't need any special macro code for syncing them, as that's already built in to klipper
22 replies
RRCRat Rig Community [Unofficial]
Created by 3DBoomer on 8/31/2024 in #ratos-support
2 in line extruders...
That's all I needed for RatOS to see my extruder properly. Make sure to update pins and values accordingly
22 replies
RRCRat Rig Community [Unofficial]
Created by 3DBoomer on 8/31/2024 in #ratos-support
2 in line extruders...
[tmc2209 extruder_stepper my_extra_stepper]
uart_pin: PC6
stealthchop_threshold: 0
interpolate: False
run_current: 0.707
sense_resistor: 0.11
driver_TBL: 0
driver_TOFF: 4
driver_HEND: 6
driver_HSTRT: 7
#driver_SGTHRS: 40

[extruder_stepper my_extra_stepper]
extruder: extruder
step_pin: PF11
dir_pin: PG3
enable_pin: !PG5
microsteps: 64
rotation_distance: 4.63
full_steps_per_rotation: 200
[tmc2209 extruder_stepper my_extra_stepper]
uart_pin: PC6
stealthchop_threshold: 0
interpolate: False
run_current: 0.707
sense_resistor: 0.11
driver_TBL: 0
driver_TOFF: 4
driver_HEND: 6
driver_HSTRT: 7
#driver_SGTHRS: 40

[extruder_stepper my_extra_stepper]
extruder: extruder
step_pin: PF11
dir_pin: PG3
enable_pin: !PG5
microsteps: 64
rotation_distance: 4.63
full_steps_per_rotation: 200
22 replies
RRCRat Rig Community [Unofficial]
Created by 3DBoomer on 8/31/2024 in #ratos-support
2 in line extruders...
Here's what I have in my config for my second extruder:
22 replies
RRCRat Rig Community [Unofficial]
Created by Jessica on 7/7/2024 in #fix-my-print
flow issues at higher speeds
Yeah, that seems to have been it. The updated print is not showing this issue at all.
8 replies
RRCRat Rig Community [Unofficial]
Created by Jessica on 7/7/2024 in #fix-my-print
flow issues at higher speeds
I'm trying again. We'll see what happens this time.
8 replies
RRCRat Rig Community [Unofficial]
Created by Jessica on 7/7/2024 in #fix-my-print
flow issues at higher speeds
I've increased the temp about 5 degrees and dropped the max flow rate on the filament profile.
8 replies